Enviro FPI - Manual - manualsarea.com

Page 2 - ENVIROFIRE INSTALLATION MANUAL; TABLE OF CONTENTS; Important; OPERATION; Parts

ENVIROFIRE INSTALLATION MANUAL TABLE OF CONTENTS INTRODUCTION Important Safety Data........................................................... 3 Pellet Quality ........................................................................ 4 Warnings and Recommendations........................................

Page 3 - IMPORTANT SAFETY DATA; SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

IMPORTANT SAFETY DATA Please read this entire manual before installation and use of this pellet fuel burning room heater. Failure to follow these instructions could result in property damage, bodily injury or even death. CAUTION: DO NOT CONNECT OT ANY AIR DISTRIBUTION DUCT OR SYSTEM; DO NOT BURN GAR...

Page 5 - WARNINGS AND RECOMMENDATIONS; AUTOMATIC SAFETY FEATURES OF YOUR PELLET STOVE; ALSO FIND THE REASONS WHY THE UNIT OVERHEATED.

WARNINGS AND RECOMMENDATIONS A. Do not abuse the glass by striking or slamming the door shut. B. Do not attempt to operate the stove with broken glass. C. Do not attempt to open the door and clean the glass while the unit is in operation. If you must clean the glass, use a soft cotton cloth and mild...

Page 6 - HOW TO START AND OPERATE YOUR PELLET APPLIANCE; TURNING YOUR PELLET STOVE OFF

HOW TO START AND OPERATE YOUR PELLET APPLIANCE 1. Check and fill hopper with pellets. 2. Switch on power by pushing the start up switch once only. 3. Turn the Dial A Fire knob to the 12 o’clock position. (Lower grade pellets may need a higher setting on the feed rate). NOTE: unit will take longer to...

Page 7 - SLIDER/DAMPER INSTALLATION /OPERATION INSTRUCTIONS; INSTALLATION; THE TUBE SCRAPER ROD:

SLIDER/DAMPER INSTALLATION /OPERATION INSTRUCTIONS This is used to regulate the airflow through the pellet stove. INSTALLATION 1. Remove the slider rod (short rod with knob and nuts) and the two nuts from their package and open the left side panel. 2. Remove the knob and outer nut from the knob. Pus...

Page 8 - AREAS FOR ROUTINE INSPECTION

AREAS FOR ROUTINE INSPECTION The following should be inspected periodically to ensure that the appliance is operating at its optimum and giving you excellent heat value: 2-3 DAYS/WEEKLY SEASONALLY or 2 TONS OF FUEL Burn Pot and Liner Exhaust Vent and Fresh Air Intake Tube Ash Pan Blower Mechanisms I...

Page 10 - ELECTRICAL COMPONENT FUNCTIONS

ELECTRICAL COMPONENT FUNCTIONS The following is a list of electrical components and their functions on the ENVIROFIRE EF-IIIi Bay pellet stove. 1. CONVECTION FAN CONTROLLER This controller is responsible for varying the speed of the convection blower. The stove does have a fan control over-ride. Sho...

Page 12 - DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE; VENT TERMINATION REQUIREMENTS

DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE 1. Check clearances to combustibles. 2. Do not obtain combustion air from an attic, garage or any unventilated space. Combustion air may be obtained from a ventilated crawlspace. 3. Do not install the stove in a bedroom. 4. You can vent the stove throug...

Page 13 - REMOVING YOUR NEW STOVE FROM IT’S PALLET; REMOVE SCREW; FIREPLACE DIMENSIONS; SURROUND

REMOVING YOUR NEW STOVE FROM IT’S PALLET To remove your new stove from its pallet, open the left and right side panels. There are two wood screws that are holding the bottom of the stove to the pallet. Remove the screws. Close the side panels. See PAGE 18 how to install the pedestal. INSERT MODEL FR...

Page 14 - MASONRY FIREPLACE INSERT INSTALLATION, MODEL FPI; CLEARANCE TO COMBUSTIBLES:

MASONRY FIREPLACE INSERT INSTALLATION, MODEL FPI The Fireplace Insert model includes surround face plates and a pedestal. When installing this unit, ensure that the pedestal is removed from its box and installed on the bottom of the unit. (Surround assembly instructions are in this manual). CLEARANC...

Page 15 - ASSEMBLING THE FACE PLATE FOR THE FPI AND BIH MODELS; STANDARD: 40” X 30 1⁄4” OVERSIZE: 46” X 33”

ASSEMBLING THE FACE PLATE FOR THE FPI AND BIH MODELS 1. To attach the pedestal, place the unit on its back, making sure not to damage the wiring, then bolt the pedestal onto the unit. Back off the screws on the base, install the pedestal over the screws. Lock in place using the keyholes, tighten the...

Page 17 - FREESTANDING INSTALLATION, MODELS FS; CLEARANCES TO COMBUSTIBLES (FREESTANDING); ALCOVE DIMENSIONS; INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER.

FREESTANDING INSTALLATION, MODELS FS CLEARANCES TO COMBUSTIBLES (FREESTANDING) - Side wall to unit A- 6 INCHES (150 mm) - Back wall to unit B- 1 INCH (25 mm) - Corner to unit C- 1 INCH (25 mm) - Mantle (Hearth Mount) 8 INCHES ( - Combustible flooring underneath the unit and extending 6 INCHES (150 m...

Page 18 - PEDESTAL INSTALLATION

MODEL FS (FREESTANDING) INSTALLATION PEDESTAL INSTALLATION : Model FS comes with a pedestal that has to be attached prior to installation: - Remove the pedestal from the box - Remove the ENVIROFIRE heater form the box. - Place the unit on its back, making sure not to damage the wiring. - Back off th...

Page 19 - HORIZONTAL EXHAUST THROUGH THE WALL

HORIZONTAL EXHAUST THROUGH THE WALL 1. NOTE: Use only listed type “PL” or “L” pellet venting products. Failure to use listed components may cause damage or personal injury or death. 2. Choose a location for your stove that meets the requirements stated in this manual and allows installation with the...

Page 20 - THROUGH WALL INSTALLATION

Page 21 - FREESTANDING INSIDE VERTICAL INSTALLATION

FREESTANDING INSIDE VERTICAL INSTALLATION 1. Choose a stove location that is ideal. See the section Deciding Where to Locate Your Pellet Appliance. 2. Place a non-combustible hearth pad where necessary. 3. Place the unit on the hearth pad and space it in a manner so when the pellet vent is installed...

Page 22 - FREESTANDING OUTSIDE VERTICAL INSTALLATION

FREESTANDING OUTSIDE VERTICAL INSTALLATION To accomplish the above titled installation, follow steps 1 through 8 in the previous section and then finish it by performing the following. 9. Install a tee with clean out on the outside of the house. 10. Install PL vent upward from the tee. Make sure tha...

Page 23 - MOBILE HOME INSTALLATION; CAUTION: THE STUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR,; OUTSIDE FRESH AIR CONNECTIONS; A Fresh air intake is strongly recommended

MOBILE HOME INSTALLATION - Secure the heater to the floor using the two bolt holes supplied in the pedestal. - CAUTION: THE STUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND CEILING/ROOF MUST BE MAINTAINED. - Ensure the unit is electrically grounded to the chassis of your home (permanent...

Page 24 - TROUBLESHOOTING; The stove will not start; The exhaust motor will not function normally

TROUBLESHOOTING DO NOT: - Hold the start-up switch down, this is a momentary contact switch and can be damaged if held down too long. - Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly. Only qualified technicians should deal ...

Page 27 - WIRING DIAGRAM

Page 28 - PARTS LIST

PARTS LIST EF-001 AUGER MOTOR EF-088A LOG SET (20-036) EF-002 CONVECTION BLOWER EF-091 FPI BRASS TRIM EF-004 CONVECTION BLOWER IMPELLER EF-092 EF3Bi GOLD DOOR COMPLETE EF-007 COMBUSTION BLOWER COMPLETE EF-093 EF3Bi GOLD DOOR ONLY EF-008 COMBUSTION MAIN IMPELLER EF-094 EF3Bi PAINTED DOOR COMPLETE EF-...

Page 31 - WARRANTY

WARRANTY Sherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one year warranty is provided on all electrical components. The above limited warranties are extended only to the original purchaser. There is no warranty on the following parts: - Glass window - ...

Enviro FPI - Manual

Table of Contents:

Summary

Other Enviro Models