Enviro 50-1628 - Manuals

5 Specifications WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. R ATING L ABEL L OCATION : The Rating Label is located on the inside surface of the pedestal control door. D IM...

6 Operating Instructions For Your Safety, Read Safety Precautions And Lighting Instructions Before Operating. WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE. Figure 2: Lighting Instruction Label. 2. St...

7 A IR S HUTTER : Air Shutter Adjustment Nut Figure 5: Air Shutter Adjustment. The air shutter is controlled by sliding the air shutter adjustment screw (shown in Figure 5) either forwards or backwards. The adjustment screw, for the primary air, is located on the bottom of the firebox. The air shutt...

Operating Instructions For Your Safety, Read Safety Precautions And Lighting Instructions Before Operating 8 The ideal flame will be blue at the base and light orange above. The flames should be of medium height. If the flames look like this (refer to Figure Figure 43 or Front Cover), no adjustment ...

9 Maintenance And Service R OUTINE M AINTENANCE : At least once a year, run through the following procedures to ensure the system is clean and working properly. Check the burner to see if all the ports are clear and clean. Check the pilot to make sure it is not blocked by anything. The pilot flame s...

Figure 9: Install the Rock Set Burner to the Firebox. 10 Maintenance And Service R EPLACING THE G LASS : IMPORTANT: Do not operate with the glass front removed, cracked or broken. The glass in the fireplace is a high temperature ceramic. If the glass is damaged in any way, a factory replacement door...

12 Maintenance And Service F UEL C ONVERSION : TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY Please read and understand these instructions before installing. Warning: This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all ...

14 Initial Installation QUALIFIED INSTALLERS ONLY WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. P REPARATION F OR I NSTALLATION : • If you are converting to a Cara DR unit, f...

Initial Installation QUALIFIED INSTALLERS ONLY P LANNING Y OUR I NSTALLATION : The Cara DR is only for horizontal rear vent installations. The maximum horizontal is 2’ (61 cm) and the slope on the vent must be 11⁄4” per foot (3.2 cm per 30 cm). No vent restrictor is required and no elbows are allowe...

16 1 In accordance with the current CSA B149, Natural Gas and Propane Installation Code. 2 In accordance with the current ANSI Z223.1 NFPA 54, National Fuel Gas Code. * These numbers are only estimates. Clearance in accordance with installation codes and the requirements of the gas supplier. t A ven...

Initial Installation QUALIFIED INSTALLERS ONLY G AS L INE C ONNECTION AND T ESTING : WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to this appliance. O L I T P TP TH TP TH IN OU T H I LO N OF O F LI P T O Manifold Pressure Tap Inlet Pressure Tap Hi/Low...

21 Initial Installation QUALIFIED INSTALLERS ONLY E LECTRICAL R EQUIREMENTS F OR G AS V ALVE AND O PTIONAL B LOWER : The ENVIRO CARA will operate without electrical power. This model has a millivolt gas control, which uses the pilot flame to generate enough electricity to operate the main burners. T...

23 Figure 39: Log Placement of Right Log. The placement of the logs is not arbitrary. If they are positioned incorrectly, the flames can be “pinched” and will not burn correctly. The burner has four (4) pins and four (4) ledges which make alignment easier. Using the pictures provided, carefully set ...

25 I NSTALLATION OF R OCK S ET : If the rocks are positioned incorrectly, the flames can be “pinched” and will not burn correctly. If the rocks are broken due to handling or shipping, replace the rocks with new ones. Using the pictures provided, carefully set the rocks in place. Secondary Installati...

26 Secondary Installation Figure 45: Rock Placement of Four Large Rocks. Figure 46: Rock Placement of Two Medium Rocks. Figure 47: Rock Placement of Seven Small Rocks. Figure 48: Rock Placement Complete. 3. The four (4) large rocks are placed across front of burner (see Figures 45 & 46). These r...

Secondary Installation Important note: When the unit is turned on for the first time, it should be turned onto high without the fan on for the first four (4) hours. This will cure the paint, rockss, gasket material and the other products used in the manufacturing process. It is advisable to open a w...

Trouble Shooting Problem Possible Cause Solution The main burner does not ignite when called for. The gas valve may not be on. • Check that the gas control knob is in the “ON” position. Thermostat is not calling for heat. • Adjust the thermostat several degrees above ambient temperature. Problem wit...

29 Parts List Reference Number Part Description Part Number 1 120°F (49°C) Ceramic Fan Temperature Sensor EC-001 Thermopile EC-012 2 S.I.T. Piezo Igniter EC-023 Domestic Power Cord - 115V EC-042 Heyco Strain Relief EC-044 3 Convection Blower (Fan) - 115V EC-069 3 Cara Fan Kit 50-1545 4 Fan Controlle...

Warranty Sherwood Industries Ltd. is the manufacturer of the VistaFlame line of heating products. At Sherwood Industries, our commitment to the highest level of quality and customer service is the most important thing we do. Each VistaFlame stove is built on a tradition of using only the finest mate...

35 Installation Data Sheet The following information must be recorded by the installer for warranty purposes and future reference. NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ ___________________...