Page 2 - ENVIROFIRE INSTALLATION MANUAL; TABLE OF CONTENTS
ENVIROFIRE INSTALLATION MANUAL TABLE OF CONTENTS 1) INTRODUCTION PAGE Important Safety Data........................................................... 3 Pellet Quality ........................................................................ 4 Warnings and Recommendations................................
Page 3 - IMPORTANT SAFETY DATA
IMPORTANT SAFETY DATA To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering to the installation instructions. An ENVIROFIRE dealer will be happy to assist you in obtaining information with regards to your local building codes and installation restrictions....
Page 5 - WARNINGS AND RECOMMENDATIONS; AUTOMATIC SAFETY FEATURES OF YOUR PELLET STOVE; ALSO FIND THE REASONS WHY THE UNIT OVERHEATED.
WARNINGS AND RECOMMENDATIONS A. Do not abuse the glass by striking or slamming the door shut. B. Do not attempt to operate the stove with broken glass. C. Do not attempt to open the door and clean the glass while the unit is in operation. To clean the glass, use a soft cotton cloth and mild window c...
Page 6 - HOW TO START AND OPERATE YOUR PELLET APPLIANCE; Heat Output; Knob B; Switch; KNOB A; TURNING YOUR PELLET STOVE OFF
HOW TO START AND OPERATE YOUR PELLET APPLIANCE Dial-A-Fire Heat Output Knob Knob B Start-up Switch Auger Light Convection Blower Speed Control KNOB A 1. Check and fill hopper with pellets. 2. Make sure unit is plugged into a working outlet. 3. Switch the power “ON” by pushing the start up switch onc...
Page 8 - AREAS FOR ROUTINE INSPECTION
AREAS FOR ROUTINE INSPECTION The following should be inspected periodically to ensure that the appliance is operating at its optimum and giving you excellent heat value: 2 3 DAYS/WEEKLY SEASON or 2 TONS OF FUEL Burn Pot and Liner Exhaust Vent Ash Pan Fresh air Intake Tube Inside Firebox Blower Mecha...
Page 10 - ELECTRICAL COMPONENT FUNCTIONS
Once you are finished using the pellet appliance for the season, unplug the stove for added electrical protection. It is very important that the stove be cleaned and serviced as stated above. (See Section Areas of Routine Inspection) 5 4 3 2 1 ELECTRICAL COMPONENT FUNCTIONS The following is a list o...
Page 13 - DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE; VENT TERMINATION REQUIREMENTS; PELLET STOVE
DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE 1. Check clearances to combustibles. 2. Do not obtain combustion air from an attic, garage or any unventilated space. Combustion air may be obtained from a ventilated crawlspace. 3. Do not install the stove in a bedroom. 4. You can vent the stove throug...
Page 14 - REMOVING YOUR NEW STOVE FROM IT’S PALLET; REMOVE SCREW; FIREPLACE DIMENSIONS
REMOVING YOUR NEW STOVE FROM IT’S PALLET To remove your new stove from its pallet, open the left and right side panels. There are two wood screws that are holding the bottom of the stove to the pallet. Remove the screws. Close the side panels. See PAGE 18 how to install the pedestal. INSERT MODEL FR...
Page 15 - MASONRY FIREPLACE INSERT INSTALLATION, MODEL FPI
MASONRY FIREPLACE INSERT INSTALLATION, MODEL FPI The Fireplace Insert model includes surround face. (Surround assembly instructions are in this manual). (SEE PAGE 15 in this manual) CLEARANCE TO COMBUSTIBLES: Side wall .................................................. 9” (200 mm) from the body of t...
Page 16 - ASSEMBLING THE FACE PLATE FOR THE FPI MODEL; FPI PEDESTAL INSTALLATION
ASSEMBLING THE FACE PLATE FOR THE FPI MODEL 1. To assemble the surround panels, lay the panels face down on a soft flat surface and align the outer edges of the sides with the top panel. Bolt the sides to the top using the hardware provided. (4 x 1/4” nuts and bolts) 2. Assemble the brass frame usin...
Page 17 - FREESTANDING INSTALLATION, MODEL FS; CLEARANCE TO COMBUSTIBLES
FREESTANDING INSTALLATION, MODEL FS CLEARANCE TO COMBUSTIBLES This unit must be installed on a noncombustible hearth pad, extending at least 6” (inches) (150 mm) in front of the appliance and at least the entire width of the appliance. -Side wall to unit A- 6 INCHES (150 mm) -Back wall to unit B- 2 ...
Page 18 - FREESTANDING PEDESTAL INSTALLATION
-Side wall to unit .................. E 6 INCHES (152 mm) -Mantle to unit F 10 INCHES (254 mm) -Top facing to unit G 8 INCHES (203 mm) -Side facing to unit H 9 INCHES (228 mm) -Floor protection D 6 INCHES (152 mm) FREESTANDING PEDESTAL INSTALLATION ASSEMBLY: Model FS comes with a pedestal that has t...
Page 19 - HORIZONTAL EXHAUST THROUGH THE WALL
HORIZONTAL EXHAUST THROUGH THE WALL 1. Choose a location for your stove that meets the requirements stated in this manual and allows installation with the least amount of interference to house framing, plumbing, wiring, etc. 2. Install a non-combustible hearth pad (where necessary). 3. Place the app...
Page 20 - THROUGH WALL INSTALLATION
Page 21 - INSIDE VERTICAL THROUGH THE ROOF INSTALLATION,
INSIDE VERTICAL THROUGH THE ROOF INSTALLATION, 1. Choose a stove location that is ideal. See the section Deciding Where to Locate Your Pellet Appliance. 2. Place a non-combustible hearth pad where necessary. 3. Place the unit on the hearth pad and space it in a manner so when the pellet vent is inst...
Page 22 - OUTSIDE VERTICAL PIPE INSTALLATION
OUTSIDE VERTICAL PIPE INSTALLATION To accomplish the above titled installation, follow steps 1 through 8 in the previous section and then finish it by performing the following. 9. Install a tee with clean out on the outside of the house. 10. Install PL vent upward from the tee. Make sure that you in...
Page 23 - MOBILE HOME INSTALLATION; OUTSIDE FRESH AIR CONNECTIONS
MOBILE HOME INSTALLATION - Secure the heater to the floor using the two holes in the pedestal. Do not disturb the structural integrity of the home. - Ensure the unit is electrically grounded to the chassis of your home (permanently). - Do not install in a room people sleep in. - Outside fresh air is...
Page 28 - WIRING DIAGRAM
Page 29 - PARTS LIST
PARTS LIST EF4i-001 AUGER MOTOR EF4i-100 RETROFIT SLIDER KIT EF4i-002 CONVECTION BLOWER EF4i-103 ASH SILL EF4i-007 COMBUSTION BLOWER EF4i-104 HOPPER LID EF4i-008 COMBUSTION MAIN IMPELLER EF4i-104A FPI HOPPER LID EF4i-009 COMBUSTION COOLING IMPELLER EF4i-105 ASH PAN LATCH FS ONLY EF4i-010 EXHAUST TEM...
Page 30 - EF 4 i
30 AUGER BRASS BUSHINGS SET of TWO EF4i-065 PIN IGNITER EF4i-127 HIGH LIMIT TEMP SENSOR 200 ° F (93 ° C) EF4i-016 CONTROL PANEL with DECAL EF4i-053 FAN CONTROLLER with KNOB EF4i-045 GREEN LIGHT EF4i-041 START-UP SWITCH EF4i-043 DIAL-A-FIRE EF4i-044 CONVECTION BLOWER EF4i-002 PHASE CONTROLLER EF4i-14...
Page 31 - EF 4 I
31 GOLD DOOR COMPLETE EF4i-092 PAINTED DOOR COMPLETE EF4i-094 FS STOVE TOP EF4I-111 STOVE TOP HANDLE BACK GRILL EF4i-097 FS LEFT CABINET SIDE EF4i-142 ASH PAN W/ LATCH EF4i-105 FS PEDESTAL (ASH PAN TYPE) EF4i-139 EF 4 I EXPLODED (STEEL COMPONENTS) Page 2 of 2 JULY 2001 ASH PAN LATCH EF4i-060 FS RIGH...
Page 32 - WARRANTY; WHEN FILLING A WARRANTY CLAIM PLEASE COMPLETE THE FOLLOWING
WARRANTY Sherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electrical components. The above limited warranties are extended only to the original purchaser. There is no warranty on the following parts: - fiberglass rope...
