Enviro 50-1386 - Manual - manualsarea.com

Page 2 - Table of Contents

Table of Contents 2 Introduction............................................................................................................3 Rating Label Location.....................................................................................3Important Safety Data.................................

Page 3 - Introduction; to the installation instructions.; Never

3 Introduction * This manual is designed for the technician in conjunction with the owner’s manual. * R ATING L ABEL L OCATION : The rating label is located on the hopper top behind the surround panel. I MPORTANT S AFETY D ATA : Please read this entire Owner’s Manual before installing or operating t...

Page 4 - ELECTRICAL: The use of a surge protected power bar is recommended.; SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

4 Introduction ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical cord should be connected to a standard 120 volts, 60 hertz electrical outlet and also must be accessible. If this power cord should become damaged, a replacement power...

Page 5 - Installation

5 Installation R EMOVING P ELLET S TOVE F ROM P ALLET : Figure 1: Removing Stove From the Pallet. Use a flathead screwdriver or 5 / 16 ” socket to remove the four (4) screws that secure the Empress FPI to the pallet. Two (2) of the screws are shown in Figure 1 and the other two (2) are in the same l...

Page 7 - DO NOT

Installation M ASONRY F IREPLACE I NSTALLATION : If installing the Empress with a skirt the skirt must be installed before the installation.A non-combustible hearth pad must cover combustible flooring underneath, as well as 6” (150 mm) in front of the heater and 6” (150 mm) to the side of the heater...

Page 11 - THE SLIDER / DAMPER MUST BE SET AT TIME OF INSTALLATION.

11 Installation S LIDER /D AMPER S ETTING : This is used to regulate the airflow through the pellet stove. THE SLIDER / DAMPER MUST BE SET AT TIME OF INSTALLATION. A Qualified Service Technician or Installer must set the Slider Damper . More Air Less Air Figure 15: Slider / damper positions. The sli...

Page 12 - Troubleshooting; flash

Troubleshooting DO NOT: ● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly. Only qualified technicians should deal with possible internal electrical failures. ● Do not remove from the firebox any screws without penetrating oi...

Page 13 - The exhaust motor will not function normally.

13 Troubleshooting ü Check the exhaust blower voltage across the blower wires (>=114V on #5 setting and >= 82V on #1 setting). – Replace the Circuit Board if the Voltage reading is less than 82V. with a line voltage >115V AC. ü Check vacuum levels in the exhaust channel by bypassing the vac...

Page 14 - The convection blower will not function normally.

Troubleshooting Auger light flashes but auger motor does not turn at all. ü If the auger gear box does not turn but the motor’s armature does try to spin then the auger is jammed. – Try to break apart jam by poking at the jam through the drop tube. If this fails then empty the hopper and remove the ...

Page 15 - Wiring Diagram

15 Connect Thermostat Here Red Red Red Red Brown Brown Brown Brown Thermostat Selector Pins White White White 115V White 220V Blue White White OrangeOrange Orange Orange Yellow Yellow Grey Grey Grey Grey Purple Purple Blue 115V Black 220V Brown Black Black Black Blue Daughter Board Vacuum Switch Com...

Page 16 - Parts List; Reference

Parts List Reference Number Description Part Number 1 120 °F (49 °C) Ceramic Fan Temperature Sensor EC-001 Domestic Power Cord - 115V EC-042 2 Auger Motor - 115V EF-001 3 High Limit Temp Sensor 200 °F (93 °C) Manual Reset EF-016 Silicone Hose EF-018 4 Ash Pan Latch EF-060 Pellet Stove Cleaning Brush...

Page 18 - Parts Diagram - Components; Empress - Fireplace Insert Components

Parts Diagram - Components 3 Empress - Fireplace Insert Components October 2006 1 9 8 11 2 12 14 21 17 16 5 10 18

Page 19 - Parts Diagram - Parts

19 Parts Diagram - Parts 6 Em pr es s -F ire pl ac e In se rt Pa rt s O ct ob er 20 06 30 32 13 22 4 18 25 23 28 24 26 27 7 31 29 19 15 20

Page 20 - Warranty; Limited Lifetime Warranty:; Here is how our Warranty works

20 Warranty Sherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to the highest level of quality and customer service is the most important thing we do. Each Enviro stove is built on a tradition of using only the finest materials...

Page 23 - Installation Data Sheet

23 NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ _________________________________________ PHONE:___________________________________ NAME OF DEALER: _________________________________________ ADDRE...

Enviro 50-1386 - Manual

Table of Contents:

Summary

Other Enviro Models