Enviro 50-1095 - Manual

Enviro 50-1095

Enviro 50-1095 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
Page: / 31

Table of Contents:

  • Page 2 – Table of Contents
  • Page 3 – Introduction; The rating label is located on the back of the unit.; to the installation instructions.; adjusting the slider damper located on the left side of the stove.; Caution: Do not connect to any air distribution duct or system.; damper as needed to ensure proper combustion.
  • Page 4 – ELECTRICAL: The use of a surge protected power bar is recommended.; The unit must be; Never; the heater while it is in use.; SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
  • Page 5 – Installation
  • Page 7 – Install vent at clearances specified by
  • Page 8 – NOTE: Venting terminals shall not be recessed into walls or siding.
  • Page 9 – Base of unit to center of flue 103⁄4” (273 mm)
  • Page 11 – pipe outside the building to help naturally draft in the unit.
  • Page 15 – Do not pass cable
  • Page 16 – blower wiring harness.
  • Page 18 – NOTE: NOT FOR USE IN GERMANY
  • Page 19 – technician using magnehelic.
  • Page 20 – This kit must be installed before the unit is started.; Installing the Panels:
  • Page 21 – Installing Hopper Lid:
  • Page 22 – Troubleshooting; flash; because the Exhaust Temperature Sensor’s contacts have opened.
  • Page 23 – The exhaust motor will not function normally.; (The Vacuum Switch contacts have opened for more than 15 sec.); To reset Circuit Board after a trouble code - push the ON/OFF button
  • Page 24 – The convection blower will not function normally.
  • Page 25 – Wiring Diagram
  • Page 26 – Parts List; Reference
  • Page 28 – Parts Diagram - Components
  • Page 29 – Parts Diagram - Steel; er
  • Page 30 – Warranty; ON AN OFFICIAL WARRANTY CLAIM FORM:
  • Page 31 – Installation Data Sheet
Loading the manual

PELLET STOVE

Bern

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE

OF THIS PELLET BURNING ROOM HEATER. FAILURE TO FOLLOW THESE

INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY

OR EVEN DEATH

Contact your building or fire officials about restrictions and installation

inspection requirements in your area.

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

TECHNICAL MANUAL

����

50-1095

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Table of Contents

2 Introduction...................................................................................................................................3 Rating Label Location................................................................................................................3 Important Safety D...

Page 3 - Introduction; The rating label is located on the back of the unit.; to the installation instructions.; adjusting the slider damper located on the left side of the stove.; Caution: Do not connect to any air distribution duct or system.; damper as needed to ensure proper combustion.

3 Introduction * This manual is designed for the technician in conjunction with the owner’s manual. * R ATING L ABEL L OCATION : The rating label is located on the back of the unit. I MPORTANT S AFETY D ATA : Please read this entire Owner’s Manual before installing or operating this ENVIRO Pellet St...

Page 4 - ELECTRICAL: The use of a surge protected power bar is recommended.; The unit must be; Never; the heater while it is in use.; SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

4 Introduction ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical cord should be connected to a standard 220-240 volts,, nominal average 0.8 Amps (1.4 Amps peak), 50 hertz electrical outlet and also must be accessible. If this power ...

Other Enviro Models

All Enviro Other