Emerson G01 - Manual

Emerson G01

Emerson G01 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
Page: / 50

Table of Contents:

  • Page 2 – Bettis Actuators G01 through G13; Instruction Manual
  • Page 4 – ENGLISH LANUAGE; BETTIS
  • Page 5 – Revision “B”; CONTENTS; SECTION 1.0 – INTRODUCTION; Add An M3 Jackscrew
  • Page 6 – SECTION 5.0 - MODULE REMOVAL AND INSTALLATION
  • Page 7 – SECTION 1 - INTRODUCTION; GENERAL SERVICE INFORMATION; NOTE: Storage time is counted as part of the service interval.; Apply the thread sealant per the manufacture's instructions.
  • Page 9 – SECTION 2 - ACTUATOR DISASSEMBLY; GENERAL DISASSEMBLY
  • Page 10 – PNEUMATIC POWER MODULE DISASSEMBLY
  • Page 11 – Do not damage o-ring groove when removing end cap from cylinder.; degrees with; Do not use pipe wrench to remove tie bars.
  • Page 13 – DRIVE MODULE DISASSEMBLY; Drive Module Disassembly.
  • Page 15 – BLIND END CAP MODULE REMOVAL; M3 HANDWHEEL OR HEX DRIVE HUB REMOVAL FROM M3 STUD.
  • Page 16 – M3 JACKSCREW DISSASSEMBLY; G01-M3 JACKSCREW DISASEMBLY FROM BLIND END CAP
  • Page 17 – EXTENDED STOP BLIND END CAP DISSASSEMBLY; SECTION 3 - ACTUATOR REASSEMBLY; GENERAL REASSEMBLY; Remove and discard all old seals and gaskets.
  • Page 18 – DRIVE MODULE REASSEMBLY; seam located ±5
  • Page 20 – HOUSING COVER SCREW QUANTITY AND TORQUE TABLE
  • Page 25 – TIE BAR NUTS
  • Page 26 – G2 AND G3 EARLY MODEL PNEUMATIC POWER MODULE REASSEMBLY
  • Page 29 – M3 JACKSCREW ASSEMBLY; G01-M3 JACKSCREW REASSEMBLY TO M3 BLIND END CAP.
  • Page 31 – M3 HANDWHEEL OR M3 HEX DRIVE HUB INSTALLATION; M3 HANDWHEEL OR HEX DRIVE HUB INSTALLATION TO M3 JACKSCREW .; EXTENDED STOP BLIND END CAP REASSEMBLY
  • Page 32 – ACTUATOR TESTING; Apply a commercial leak testing solution to the following areas:; SECTION 4 - FIELD CONVERSIONS
  • Page 34 – ADD AN M3 JACKSCREW TO SPRING MODULE; To install the M3 Handwheel or M3 drive hub refer to Section 3.7.; ADD AN EXTENDED STOP (ES) TO BLIND END CAP MODULE; Remove blind end cap module per Section 2.4.; ADD AN EXTENDED STOP (ES) TO POWER MODULE OUTER END CAP
  • Page 35 – SECTION 5 - MODULE REMOVAL AND INSTALLATION; Pneumatic Power Module removal or disassembly.; DO NOT REMOVE SPRING MODULE WHILE SPRING IS COMPRESSED; screws are loosened or removed.
  • Page 36 – The maximum pressure to be applied in step 5.1.10 is 25 PSIG.; cartridge tension rod hex nut out of it's cast hex seat.
  • Page 37 – SPRING MODULE INSTALLATION
  • Page 41 – PNEUMATIC POWER MODULE REMOVAL
  • Page 43 – G2 THRU G13 POWR SWIVL REMOVAL
  • Page 44 – SECTION 6 - ACTUATOR SUPPORT INFORMATION; MODULE WEIGHTS BY ITEM NUMBER AND ACTUATOR HOUSING SIZE
Loading the manual

www.Fisher.com

D102754X012

Bettis

r

Service Instructions for Models G01

through G13 Pneumatic Actuators

The following instruction manual is for the Bettis
Actuator. This instruction manual was prepared by
Bettis, a member of the Valve Automation Division of
Emerson Process Management

t

. Please contact

Bettis to ensure that the following instruction manual
is the most recent one available.

Do not install, operate, or maintain this product
without first

D

being fully trained and qualified in

valve, actuator, and accessory installation, operation
and maintenance, and

D

carefully reading and

understanding the contents of this manual. Emerson
Process Management is not responsible for the
content

of this manual. If you have any questions about
these instructions, contact the actuator manufacturer
before proceeding.

Note

Neither Emerson, Emerson Process
Management, nor any of their affiliated
entities assumes responsibility for the
selection, use and maintenance of any
product. Responsibility for the
selection, use, and maintenance of any
product remains with the purchaser
and end-user.

Instruction Manual

Form 5653
February 2007

Bettis Actuators G01 through G13

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Bettis Actuators G01 through G13; Instruction Manual

Bettis Actuators G01 through G13 Instruction Manual Form 5653 February 2007 2 Emerson Process Management Marshalltown, Iowa 50158 USACernay 68700 France Sao Paulo 05424 BrazilSingapore 128461 www.Fisher.com The contents of this publication are presented for informational purposes only, and while eve...

Page 4 - ENGLISH LANUAGE; BETTIS

ENGLISH LANUAGE BETTIS SERVICE INSTRUCTIONS FOR MODELS G01 THROUGH G13 PNEUMATIC ACTUATORS PART NUMBER: 124840E REVISION: “B” DATE: 17 December 2001

Page 5 - Revision “B”; CONTENTS; SECTION 1.0 – INTRODUCTION; Add An M3 Jackscrew

Bettis P/N 124840E Revision “B” Page 1 of 46 CONTENTS SECTION 1.0 – INTRODUCTION PAGE 1.1 General Service Information ................................................................... 3 1.2 Definitions ............................................................................................... ...

Other Emerson Models