Emerson 3095 - Manual

Emerson 3095

Emerson 3095 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
Page: / 32

Table of Contents:

  • Page 2 – Quick Installation Guide; Rosemount 3095 MultiVariable; Emerson Process Management GmbH & Co. OHG; IMPORTANT NOTICE; Explosions could result in death or serious injury:; when power is applied to the unit.; Process leaks may cause harm or result in death.; leads can cause electrical shock.
  • Page 3 – RANSMITTER
  • Page 4 – TEP; Liquid Flow Applications; valves are oriented upward.; Gas Flow Applications; Panel Mount; Pipe Mount
  • Page 5 – Consider Housing Rotation; To improve field access or to better view the optional LCD display:; Field Installation; Mount the transmitter; Bolt Material
  • Page 6 – fieldbus devices), which is located on the front of; HART Electronics Board; fieldbus Electronics Board
  • Page 7 – • Installing a Shielded 3095 RTD Cable (See Figure 4); • Installing a ATEX/IECEx Flameproof 3095 RTD Cable (See Figure 5); Check all process connections for leaks.
  • Page 8 – Bolting Considerations; Use the following bolt installation procedure:; Coplanar Flange
  • Page 9 – O-rings with Flange Adapters; WARNING
  • Page 10 – 095 Engineering Assistant (EA) for HART Software Installation
  • Page 11 – Installing the HART Modem; Fieldbus
  • Page 12 – Use the following steps to wire the transmitter:; NOTE; conduit connections and the transmitter housing.
  • Page 13 – Do not attach shield to ground.; Approval Option Code
  • Page 14 – Setting the Loop to Manual; Configure; Step through the Flow Configuration wizard.; Configuration Properties; Basic Setup; Basic Configuration Parameters; Fast Key Sequence
  • Page 16 – Send the Configuration to the Transmitter; To configure the AI Block; AI Block configuration parameters; Parameters
  • Page 17 – Zero Trim; Using the Field Communicator; Follow the commands to perform a zero trim.; Using the Foundation Fieldbus AI Block; not; Fast Keys
  • Page 18 – RODUCT; Approved Manufacturing Locations; Emerson Process Management complies with the ATEX Directive.; Rosemount 3095 HART Hazardous Locations Certifications; North American Certifications
  • Page 19 – European Certifications; II 1 G; Special Conditions for Safe Use
  • Page 20 – II 3 G; II 1 D
  • Page 21 – INMETRO Certifications; Group
  • Page 22 – 095 Series transmitter with temperature sensor have; The temperature of process medium should be less than 121 °C.
  • Page 23 – medium is as following.; Maximum Temperature of
  • Page 24 – Combinations of Certifications; Rosemount 3095 with Fieldbus; Ordinary Location Certification for Factory Mutual
  • Page 25 – FM Approvals
  • Page 27 – FISCO
  • Page 28 – A and J combination
Loading the manual

www.rosemount.com

¢00825-0100-4716/¤

Quick Installation Guide

00825-0100-4716, Rev DA
October 2009

Rosemount 3095 MultiVariable

Start

End

Step 1: Mount the Transmitter

Step 2: Transmitter Installation

Step 3: Software Installation

Step 4: Connect the Wiring and Power Up (HART or Fieldbus)

Step 5: Configure the Transmitter (HART or Fieldbus)

Step 6: Trim the Transmitter

Product Certifications

Rosemount 3095 MultiVariable

™

Mass Flow

Transmitter with HART

®

or F

OUNDATION

™

Fieldbus Protocol

Rosemount 3095MF Series Flowmeter Transmitter

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Quick Installation Guide; Rosemount 3095 MultiVariable; Emerson Process Management GmbH & Co. OHG; IMPORTANT NOTICE; Explosions could result in death or serious injury:; when power is applied to the unit.; Process leaks may cause harm or result in death.; leads can cause electrical shock.

Quick Installation Guide 00825-0100-4716, Rev DA October 2009 Rosemount 3095 MultiVariable 2 © 2009 Rosemount Inc. All rights reserved. All marks property of owner. Rosemount and the Rosemount logotype are registered trademarks of Rosemount Inc. Rosemount Inc. 8200 Market BoulevardChanhassen, MN USA...

Page 3 - RANSMITTER

Quick Installation Guide 00825-0100-4716, Rev DAOctober 2009 Rosemount 3095 MultiVariable 3 T RANSMITTER E XPLODED V IEW Housing O-ring Cover Housing Locking Screw RTD Connector Process Adapter O-ring Electronics Board Nameplate Module O-ring Sensor Module Drain/Vent Valve Flange Adapter O-ring Opti...

Page 4 - TEP; Liquid Flow Applications; valves are oriented upward.; Gas Flow Applications; Panel Mount; Pipe Mount

Quick Installation Guide 00825-0100-4716, Rev DA October 2009 Rosemount 3095 MultiVariable 4 S TEP 1: M OUNT THE T RANSMITTER Figure 1. Using a Mounting Bracket Liquid Flow Applications 1. Place taps to the side of the line.2. Mount beside or below the taps.3. Mount the transmitter so that the drain...

Other Emerson Models