Edimax ES-5816PGH - Manual

3     Specifications ¾ Standard IEEE 802.3 10BaseT IEEE 802.3u 100BaseTX IEEE 802.ab 1000BaseT IEEE 802.3z 1000BaseSX/LX IEEE 802.3x Flow Control IEEE 802.3 Auto Negotiation IEEE 802.3 Auto-MDI/MDI-X IEEE 802.1ad Provider Bridge ( Q in Q ) IEEE 802.1x Port-based Network Access Control IEEE 802.1Q VL...

4     Package Contents Before you start to install this switch, please verify your package that contains the following items: z One Switch z One Power Cord z One User Manual z One pair Rack-mount kit + 8 Screws

5     Hardware Description This part primarily presents hardware of the web-smart switch, physical dimensions and functional overview would be described. Physical Dimensions/ Weight 45 × 440 × 330 mm (H × W × D) / 4.4KG Front Panel The front Panel of the web-smart Switch consists of 16 gigabit RJ-45...

6     Rear Panel The 3-pronged power plug is placed at the rear panel of the switch right side shown as below. Hardware Installation Set the switch on a large flat space with a power socket close by. The flat space should be clean, smooth, level and sturdy. Make sure there is enough clearance around...

7     Software Description This part instructs user how to set up and manage the switch through the web user interface. Please follow the description to understand the procedure. At the first, open the web browser, and go to 192.168.2.1 site then the user will see the login screen. Key in the passwo...

8     After the user login, the right side of website shows all functions as Fig. 1-2. Figure 1-2 Configuration System System Configuration This page shows system configuration information. User can configure information as below:

11     ¾ Power Saving Mode : Adjusts the power provided to ports based on the length of the cable used to connect to other devices. Only sufficient power is used to maintain connection requirements. ¾ Mode: allow user to manually set the port speed such as Auto, 10 half, 10 Full, 100 Half, 100 Full,...

12     Figure 2-3 Aggregation Port trunk allows multiple links to be bundled together and act as a single physical link for increased throughput. It provides load balancing, and redundancy of links in a switched inter-network. Actually, the link does not have an inherent total bandwidth equal to the...

13     LACP IEEE 802.3ad Link Aggregation Control Protocol (LACP) increases bandwidth by automatically aggregating several physical links together as a logical trunk and providing load balancing and fault tolerance for uplink connections. LACP Port Configuration ¾ Port: The port number. ¾ Enabled: E...

14     RSTP IEEE 802.1w Rapid Spanning tree protocol (LACP) provides a loop-free network and redundant links to the core network with rapid convergence to ensure faster recovery from failed links, enhancing overall network stability and reliability. RSTP System Configuration ¾ System Priority: This ...

16     and forward it to another remote RADIUS authentication server to verify access rights. The EAP packet from the RADIUS server also contain the authentication method to be used. The client can reject the authentication method and request another, depending on the configuration of the client sof...

17     between hosts connected to the switch and multicast routers in the network. When a switch hears an IGMP report from a host for a given multicast group, the switch adds the host’s port number to the multicast list for that group. And, when the switch hears an IGMP Leave, it removes the host’s ...

18     ¾ Port to Mirror to: The port that will “duplicate” or “mirror” the traffic on the source port. Only incoming packets can be mirrored. Packets will be dropped when the available egress bandwidth is less than ingress bandwidth. ¾ Ports to Mirror: Select the ports that you want to mirror from t...

21     Figure 2-9-5 Filter Configuration   There are 3 mode that you can choice for filter configuration: Disabled: this mode is protected from potential threats like hackers, if the traffic from illegal MAC addresses will not be forwarded by the switch. Static: This table displays the static MAC ad...

25     Monitorning Statistic Overview Statistic Overview for all ports User can mirror traffic from any source port to a target port for real-time analysis the following figures shows clearly the statistics overview. Figure 3-1 Detailed Statics To view the statistics of individual ports, click one o...

27     RSTP Status RSTP VLAN Bridge Overview Figure 3-4 ¾ Hello Time: Interval (in seconds) at which the root device transmits a configuration message. ¾ Max Age: The maximum time (in seconds) a device can wait without receiving a configuration message before attempting to reconfigure. All device po...

28     ¾ Root ID : The priority and MAC address of the device in the Spanning Tree that this switch has accepted as the root device, and the port connected to the root device. RSTP Port Status ¾ Port/Group: The number of a port or the ID of a static trunk. ¾ Path Cost: The cost for a packet to trave...

29     Figure 3-5 VeriPHY VeriPHY Cable Diagnostics User can perform cable diagnostics for all ports or selected ports to diagnose any cable faults (short, open etc..) and feedback a distance to the fault. ¾ Cable Diagnostics: Cable diagnostics is performed on a per-port basis. Select the port numbe...

30     The following are some results of the ping command: ¾ Normal response: The normal response occurs in one to ten seconds, depending on network traffic. ¾ Destination does not respond: If the host does not respond, a “timeout” appears in ten seconds. ¾ Destination unreachable: The gateway for t...

31     Figure 3-7-2 Figure 3-7-3 Maintenance Warm Restart Press Yes button to restart the switch, the reset will be complete when the power lights stop blinking.

32     Figure 4-1 Factory Default Forces the switch to restore the original factory settings. To reset the switch, select “Reset to Factory Defaults” from the drop-down list and click Apply. The LAN IP Address, Subnet Mask and Gateway IP Address will be reset to their factory Figure 4-2 Software upl...

33     Figure43-4 Logout The administrator has write access for all parameters governing the onboard agent. User should therefore assign a new administrator password as soon as possible, and store it in a safe place. Figure 4-5                          

34     Reset button for the factory default setting   Please take the following steps to reset the Web Smart Switch back to the original default:   Step 1: Turn on the Web Smart Switch Step 2: Press and hold the reset button continuously for 5 seconds and release the reset button. Step 3: The switch...