Eaton ESWA6550SC - Manual
Eaton ESWA6550SC – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – EATON CORPORATION Cutler-Hammer; Speaker Installation; Speaker cable should be run to each speaker location prior to; To Install; Mounting Brackets on Rear of Speaker (Locked In); Caution; Mounting Brackets in the “in” Position
- Page 3 – Mounting Brackets Opened to Grip Into Drywall; Adjusting Swivel Tweeters; Speaker With Adjustable Swivel Tweeters; : Too much pressure during this procedure can cause; Adjusting the Tweeter; Reapplying the Speaker Grill; Push Evenly the Grill Back Onto the Speaker Frame; Setting Level Controls; Remove the speaker grill from the speaker frame.
- Page 4 – Speaker Specifications; SPECIFICATION
PRELIMINAR
Y DRAFT
Installation Instructions for Wall and
Ceiling Mounted Speakers
ESWA6550SC, ESWA6500SC, ESWA0800SC, ESWA6500SW
Installation Manual IM00412012E
Proof #3 — Zoltun Design — May 2, 2006
New Information
Effective May 2006
Wall and Ceiling Mounted Speaker Installation
Instructions
Prior to Installation
Each speaker requires one speaker wire set consisting of a positive
and negative wire. Eaton recommends using an 18 gauge wire or
larger for the best quality sound.
Speaker cable should be run to each speaker location prior to speaker
installation. In new construction applications, run the speaker wire to
the speaker locations prior to drywalling.
Speaker Grill Removed From Frame
Choosing the Speaker Location
Before you install your speakers you should carefully consider their
location to ensure the best quality sound. Make sure to note the loca-
tion of lighting fixtures, electrical wiring, plumbing, HVAC ducting, or
any other possible obstructions.
Once you have selected the area for installation, locate the studs or
joists nearest to the desired location. By marking the location of the
stud or joist first, you can avoid cutting into it as you cut the speaker
hole. A speaker cutout template is included to help you measure cut-
out dimensions.
Position the template into the desired location and outline the
speaker opening. If you are still not sure of possible obstructions, cut
a small hole in the center of your mounting location. This small hole
will allow you to check for obstructions behind the surface prior to
cutting out the entire speaker hole.
If there are no problems with your mounting location, proceed to cut
out the outlined hole. If the area where the speaker will be placed is
not already insulated, Eaton suggests adding insulation, Dacron, or
some other sound dampening material. If you add insulation with a
foil layer, make sure to mount the foil side away from the speaker
magnet.
Ceiling Placement
Speakers placed into the ceiling should be mounted above or as close
to the listening area as possible. Take furniture arrangements into
consideration when finalizing your speaker locations. The tweeters
located in the speakers can be adjusted to point towards the listening
area of the room.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
PRELIMINAR Y DRAFT Proof #3 — Zoltun Design — May 2, 2006 2 EATON CORPORATION Cutler-Hammer Wall and Ceiling Mounted Speakers Installation Manual IM00412012E Effective: May 2006 Speaker Installation Note: Speaker cable should be run to each speaker location prior to speaker installation. In new cons...
PRELIMINAR Y DRAFT Proof #3 — Zoltun Design — May 2, 2006 EATON CORPORATION Cutler-Hammer Wall and Ceiling Mounted Speakers Installation Manual IM00412012E Copyright 2006 3 Speaker Installation (continued) Make sure that the speaker is level and carefully tighten the mount-ing screws to secure the s...
PRELIMINAR Y DRAFT Proof #3 — Zoltun Design — May 2, 2006 Eaton Electrical Inc. 1000 Cherrington ParkwayMoon Township, PA 15108-4312United Statestel: 1-800-525-2000www.EatonElectrical.com © 2006 Eaton CorporationAll Rights ReservedPrinted in USAPublication No. IM00412012E / Z4072May 2006 Speaker Spe...
