Dewalt DW9108- User Manual

Page 3 - SAVE THESE INSTRUCTIONS; Definitions: Safety Guidelines

1 IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D E WALT TOOL, CALL US AT: 1800 654 155 (Aust) or 0800 339258 (NZ). SAFETY INSTRUCTIONS FOR POWER TOOLS When using power tools, always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and pe...

Page 4 - Electrical Safety

2 c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any...

Page 5 - Extension Cords

3 • Replacement of the supply cord. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised D E WALT Service Centre in order to avoid a hazard. Extension Cords CAUTION: Use only extension cords that are approved by the country’s Electrical Authority. Before using exte...

Page 6 - Important Safety Instructions for All Battery Packs; READ ALL INSTRUCTIONS

4 DANGER: Electrocution hazard. Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or dam...

Page 7 - The RBRCTM Seal; Rechargeable Battery Recycling Corporation.; Important Safety Instructions for all Battery Chargers

5 SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (LI-ION) • Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithium ion battery packs are burned. • If battery contents come i...

Page 8 - otherwise damaged in any way.; Using Automatic Tune-UpTM Mode

6 • An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of pow...

Page 9 - Charge Indicators; PROBLEM POWER LINE; Important Charging Notes

7 Charge Indicators Some chargers are designed to detect certain problems that can arise with battery packs. Problems are indicated by the red light flashing at a fast rate. If this occurs, re-insert battery pack into the charger. If the problem persists, try a different battery pack to determine if...

Page 10 - OPERATION; installing attachments or accessories.; Make sure your battery pack is fully charged.; To install the battery pack into the tool handle; , align the notch inside the tool’s; SAVE THESE INSTRUCTIONS FOR FUTURE USE

8 OPERATION WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/ installing attachments or accessories. FIG. 2 G FIG. 3 Installing and Removing the Battery Pack (Fig. 2, 3) NOTE: Make sure your battery ...

Page 13 - MAINTENANCE; Cleaning; CHARGER CLEANING INSTRUCTIONS; Repairs

11 Screwdriver Operation (Fig. 6) 1. Select the desired speed/torque range SCREWDRIVING FIG. 6 C using the dual range gear selector to match the speed and torque of the planned operation. 2. Turn the torque adjustment collar to the desired position. Lower numbers indicate lower torque settings; high...

Page 16 - WALT

Battery Output Chargers/Charge Time Nominal 240 Volts 12 Volts X Indicates that the battery pack is not compatible with that specific charger. All charge times are approximate. Actual charge time may vary. Read the instruction manual for more specific information. The battery voltage is nominal, it ...

Table of Contents:

Other Manuals for Dewalt DW9108

Summary

Other Dewalt Models