Dewalt 550 - Manual

9 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 MAINTENANCE All components should be periodically cleaned and coated with a light film of oil. Use a clean, non-detergent oil, preferably SAE 10 (90 SSU or lighter.) The Cutting Wheel should be replaced if worn or damaged. The Cutting Wheel life d...

10 TRI TOOL INC. 92-0116 : Rev. 060810 OPERATION Read the operating instructions carefully before attempting to operate the Model 550Tube Severing Tool. Be sure to use eye protection at all times when operating the Model 550. Select the proper Model 550 for the size of tubing to be severed. Maximum ...

11 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 NOTE: Select the proper Tri Tool Inc. Drive Unit that best suits the operation needed to beperformed. Drive Input Location A non Tri Tool Inc. Drive Unit will void the warranty. If input is counterclockwise, sever damage will occur during cutting...

13 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 WARNING: REPAIRS AND REPLACEMENT Cutter Wheel Replacement Disconnect the Drive Unit from the Model 550 Tube Cutter prior to any repairsor replacements. Rotate the drive shaft manually clockwise to rotate the cutter carriage to the desiredposition...

15 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 AIR DRIVE ASSEMBLY REMOVAL OF A SHEARED ROLL PIN FROM THE DRIVE ASSY. Push the Air Drive Assy into the Model 550 Tube Cutter and rotate it clockwise andpull it out. Unscrew the Bayonet Mounting Tube from the Motor Housing by rotating theBayonet M...

16 TRI TOOL INC. 92-0116 : Rev. 060810 TROUBLE SHOOTING Problem: The Tool Bit Chatters Probable causes: The tool bit is loose or overextended.The tool bit is damaged.The tool holder is too loose in the slides.The cutting speed is too fast.The clamping pads are loose on the pipe or tube.Cutting fluid...

18 TRI TOOL INC. 92-0116 : Rev. 060810 ACCESSORIES The following accessories are recommended for use with the Model 550 Tube Cut-ters and are available from TRI TOOL INC. 1. Portable Air Filter (P/N 75-0115) 2. Drive Assembly, Air (P/N 04-0084) 3. Shaft Assembly, 18” Flexible (P/N 14-0036) 4. Motor ...

19 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 MODEL 550-03, 04, 05, AND 06 TUBE SEVERING TOOL ASSEMBLY (P/N 01-XXXX) ILLUSTRATED PARTS BREAKDOWN 1 10 2 3 4 5 7 6 8 9 11 12 13 15 14 17 16 25 10 22 18 24 26 23 21 20 4 9 19

20 TRI TOOL INC. 92-0116 : Rev. 060810 02-2057 CARRIAGE ASSEMBLY, CUTTER 1 1. 19-0353 HOUSING, CARRIAGE, TUBE CUTTER 1 2. 32-0003 PIN, ROLL, 1/16" DIA X 1/2" 1 3. 32-0179 PIN, DOWEL, 3/16" DIA X 5/8" 1 4. 32-0226 PIN, DOWEL, 3/16" DIA X 1" LONG 2 5. 32-0251 PIN, CUTTER 1 6. 3...

43 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 The DeWALT Cordless Drill/Driver comes with an 'Instruction Manual' and should bereferenced for all safety and operating procedures. DEWALT SAFETY INSTRUCTIONS