Dewalt 37-360 - Manual

5 A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will...

6 3. Grounded, cord-connected machines intended foruse on a supply circuit having a nominal rating between150 - 250 volts, inclusive: If the machine is intended for use on a circuit that has anoutlet that looks like the one illustrated in Fig. C, themachine will have a grounding plug that looks like...

7 DEFINITIONS OF JOINTING AND PLANING OPERATIONS Fig. 2 Fig. 3 JOINTING OPERATIONS – Jointing cuts or edge jointing is the simplest and most common operation which can be done on the jointer and these cuts are made to square an edge of a workpiece. The fence is square with the table andthe depth of ...

9 REMOVING MACHINE FROM SHIPPING SKID Fig. 5 Fig. 6 Fig. 7 1. Open door (A) Fig. 5, under infeed table and remove mounting hardware that fastens infeed end of machine to skid 2. Remove three screws (B) Fig. 6, and remove cover (C) from dust chute located under outfeed table. Remove mounting hardware...

11 SINGLE PHASE INSTALLATION Fig. 12 A B Fig. 13 Fig. 14 1. Remove screw (A) Fig. 12, and terminal strip cover (B). 2. Remove plastic covering (C) Fig. 13, that snaps into terminal strip. 3. Bring power line through access hole in bottom of terminal strip box and connect the two power lines totermin...

12 Fig. 16 Fig. 17 THREE PHASE INSTALLATION If the motor on your machine is wired for 200, 230 or 460 Volts, Three Phase, proceed as follows when connectingyour machine to an electrical power system. 1. Remove screw (A) Fig. 15, and terminal strip cover (B). 2. Remove plastic covering (C) Fig. 16, t...

13 OPERATING CONTROLS AND ADJUSTMENTS Fig. 18 Fig. 19 Fig. 20 Fig. 21 START-STOP SWITCH The start-stop switch is conveniently located on a post,behind the jointer fence, for easy accessibility. To startthe machine, simply press the start button (A) Fig. 18,and to stop the machine, press the stop but...

16 Fig. 30 OUTFEED TABLEADJUSTMENTS For most jointing operations the outfeed table must beexactly level with the knives at their highest point ofrevolution. To move the outfeed table, loosen lock handle( A ) Fig. 30, and move the table raising and lowering hand lever(B) up or down until the table is...

18 The following directions will give the beginner a start on jointer operations. Use scrap pieces of lumber to checksettings and to get the feel of the operations before attempting regular work. THE KNIVES ON THE JOINTER WILL NOT WEAR EVENLY BY FEEDING THE WOOD THROUGH THE SAME SPOT ON THE TABLE EV...

19 Fig. 37 Fig. 38 Fig. 39 JOINTING AN EDGE This is the most common operation for the jointer. Set theguide fence square with the table. Depth of cut should bethe minimum required to obtain a straight edge. Hold thebest face of the piece firmly against the fence throughoutthe feed as shown in Fig. 3...

20 TAPER CUTS One of the most useful jointer operations is cutting an edge to a taper. The method can be used on a wide variety of work.Tapered legs of furniture are a common example. Instead of laying the piece on the infeed table, lower the forward end of the work onto the outfeed table. Do this v...

21 REMOVING, REPLACING AND SETTING KNIVES If the knives are removed from the cutterhead for replacement or regrinding, care must be used in removing, replacingand resetting them as follows:1. DISCONNECT THE MACHINE FROM THE POWER SOURCE . 2. Move the fence to the right until it is clear of the cutte...

23 MAINTENANCE KEEP MACHINE CLEAN Periodically blow out all air passages with dry compressedair. All plastic parts should be cleaned with a soft dampcloth. NEVER use solvents to clean plastic parts. They couldpossibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses whileusi...

24 The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw...