Dewalt 50-761 - Manual - manualsarea.com

Page 3 - SAFETY GUIDELINES - DEFINITIONS

3 Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in mi...

Page 4 - GENERAL SAFETY RULES

4 GENERAL SAFETY RULES READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,fire, and/or serious personal injury or property damage. IMPORTANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY,...

Page 5 - POWER CONNECTIONS

5 A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will...

Page 6 - EXTENSION CORDS; FOREWORD; FUNCTIONAL DESCRIPTION; MINIMUM GAUGE EXTENSION CORD

6 EXTENSION CORDS Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong grounding typeplug and matching receptacle which will accept themachine’s plug. When using an extension cord, be sureto use one heavy enough to carry the...

Page 7 - CARTON CONTENTS

7 1. Motor and blower assembly 2. Stand 1 2 Fig. 1 CARTON CONTENTS 3 4 5 6 7 8 9 3. Dust intake port 4. Cloth-covered bag retainer ring (2) 5. One micron upper filter bag (2) 6. Six mil plastic lower bag (4) 7. Legs (2) 8. Bag retainer clamp (2) 9. Bag hanging rod (2) Fig. 1A

Page 8 - UNPACKING AND CLEANING

8 10 11 12 13 14 15 16 17 Fig. 1B 10. Caster (4)11. Intake cap and ring (3)12. Bracket for bag hanging rod (2)13. Knob for attaching legs to blower/motor assembly (4)14. 3/8” (9.5mm) Lockwasher for attaching casters to stand (4)15. 5/16” (8mm) Flat washers for attaching legs to blower/motor assembly...

Page 9 - ASSEMBLY; CASTERS; ASSEMBLY TOOLS REQUIRED

9 FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTIONMANUAL. ASSEMBLY CASTERS 1. Turn stand (A) upside down, as shown in Fig 1C.2. Place 3/8” lockwasher on caster stud (B) and screw caster in...

Page 10 - ATTACHING DUST INTAKE PORTS; ALTERNATE SETUP

10 Fig. 5 Fig. 4 ATTACHING DUST INTAKE PORTS Place dust intake port (A) Fig. 7 over intake hole (B)opposite the motor. Align four holes (C) in the port withthe ones in the motor/blower assembly and fasten withfour M4 sheet metal screws. Turn unit over so casters are on the ground. BECAUSE OF THE WEI...

Page 11 - ATTACHING DUST COLLECTION BAG

11 A Fig. 8 Fig. 9 B Fig. 10 Fig. 10A A B B A B A ATTACHING DUST COLLECTION BAG USING CLOTH COVERED FLEXIBLE RING: 1. Take cloth-covered bag retainer ring (A) Fig. 8 and place it inside opening of clear plastic dustcollection bag. Fold about 6 inches of the bagdown around the retainer ring. 2. Place...

Page 12 - ATTACHING TOP FILTER BAG

12 Fig. 13 A B C D Fig. 11 Fig. 12 A B A ATTACHING ACCESSORY HOSETO INTAKE PORT DISCONNECT MACHINE FROM POWERSOURCE BEFORE CONNECTING OR DISCONNECTING HOSE . Model 50-761 provides three 4” dust ports. Proceed asfollows for each port with your accessory hoses. NOTE: Place open end (D) of intake cap r...

Page 13 - OPERATION

13 FOR OPERATOR SAFETY, DO NOT OPERATE THE MACHINE WITH ANY DUST INTAKE HOLESUNCOVERED. THE ROTATING FAN LOCATED INSIDE THE BLOWER HOUSING IS ACCESSIBLE THROUGH THE DUST IN-TAKE PORT AND CAN BE HAZARDOUS. ALWAYS WEAR PROPER APPAREL. DO NOTWEAR JEWELRY AND KEEP FINGERS AND ALL FOREIGN OBJECTS OUT OF ...

Page 14 - MAINTENANCE; PARTS, SERVICE OR WARRANTY ASSISTANCE; ACCESSORIES; Two Year Limited New Product Warranty; KEEP MACHINE CLEAN; FAILURE TO START; SERVICE

14 MAINTENANCE PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta...

Page 15 - NOTES

Page 16 - DELTA SERVICE CENTERS; CANADIAN PORTER-CABLE

The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II...

Dewalt 50-761 - Manual

Table of Contents:

Summary

Other Dewalt Models