Page 2 - CONTENTS; SECTION
2 099800 Flame-Out Information .................................................................. 3 Product Identification .................................................................... 4 Unpacking ...................................................................................... 5 Assembl...
Page 3 - WARNINGS; SAFETY; Carbon Monoxide Poisoning:; DANGER; Carbon monoxide poisoning may lead to death!
3 099800 ! WARNINGS IMPORTANT: Read this owner’s manual carefully and completelybefore trying to assemble, operate, or service this heater. Improperuse of this heater can cause serious injury or death from burns, fire,explosion, electrical shock, and carbon monoxide poisoning. SAFETY INFORMATION Carb...
Page 5 - UNPACKING; dealer where you bought heater.; ASSEMBLY; Tools Needed; Slide axle through wheel support frame. Install wheels on axle.
5 099800 UNPACKING 1. Remove all packing items applied to heater for shipment.2. Remove all items from carton.3. Check items for any shipping damage. If heater is damaged, promptly inform dealer where you bought heater. ASSEMBLY (For 90,000 and 150,000 BTU/Hr Models Only) These models are furnished ...
Page 6 - The Ignition System:; FUELS; WARNING
6 099800 THEORY OF OPERATION The Fuel System: The air pump forces air through the air line. The air is then pushed through the burner head nozzle. This air causes fuel to lift from the tank. Afine mist of fuel is sprayed into the combustion chamber. The Air System: The motor turns the fan. The fan p...
Page 7 - To Start Heater; Follow all ventilation and safety information.
7 099800 VENTILATION OPERATION Continued Figure 6 - Flame-Out Control ResetButton, 30/70,000 BTU/Hr Models Figure 7 - Flame-Out Control ResetButton, 90,000 BTU/Hr Model ! WARNING Follow the minimum fresh, outside air ventilationrequirements. If proper fresh, outside air ventilation is notprovided, c...
Page 8 - OPERATION; PREVENTATIVE; Item; To Stop Heater; STORAGE
8 099800 OPERATION Continued Figure 8 - Flame-Out Control Reset Button, 150,000 BTU/Hr Model Continued PREVENTATIVE MAINTENANCE SCHEDULE Item How Often How To Fuel tank Flush every 150-200 hours See Storage above. of operation or as needed. Air output and Replace every 500 hours of See Air Output, A...
Page 9 - SHOOTING
9 099800 Continued Item How Often How To Spark plug Clean and regap every 600 See Spark Plug, pages 12 and 13. hours operation or replace as needed. Fan blades Clean every season or as needed. See Fan, page 19. Motor Not required/permanently lubricated. TROUBLE- SHOOTING OBSERVED FAULT POSSIBLE CAUS...
Page 10 - Fuel Filter; SERVICE; Upper Shell Removal
10 099800 150 SHELL REMOVAL EA/EB Euro PV 020 UpperShell FanGuard Figure 12 - Fuel Filter Removal, 30/70,000 BTU/Hr Models Figure 11 - Upper Shell Removal, 150,000 BTU/Hr Model Figure 9 - Upper Shell Removal,30/70,000 BTU/Hr Models Figure 10 - Upper Shell Removal,90,000 BTU/Hr Model UpperShell FanGu...
Page 11 - Remove side cover screws; Connect fuel tube to burner
11 099800 100 FUEL FILTER REMOVAL PFA/P 041 150 FUEL FILTER REMOVAL PFA/P 043 Fuel Filter (90,000 BTU/Hr Model) 1. Remove side cover screws using 5/16" nut-driver. 2. Remove side cover.3. Pull upper fuel line off fuel filter neck. 4. Carefully pry bushing, lower fuel line, and fuelfilter out of ...
Page 12 - Spark Plug
12 099800 Spark Plug (30,000 BTU/Hr Model) 1. Remove upper shell (see page 10). 2. Remove fan (see page 19).3. Remove fuel and air line h o s e s f r o m n o z z l eassembly. 4. Remove spark plug wire from spark plug. 5. Remove two screws using 5/16" nut-driver andremove burner strap. 6. Place h...
Page 13 - Remove spark plug from
13 099800 Spark Plug (70/90/150,000 BTU/Hr Models) 1. Remove upper shell (see page 10). 2. Remove fan (see page 19).3. Remove spark plug wire from spark plug. 4. Remove spark plug from burner head using 13/16"open-end wrench. 5. Clean and regap spark plug electrodes to 1.4 mm gap. 6. Install spa...
Page 15 - Nozzle
15 099800 Nozzle (30,000 BTU/Hr Model) 1. Remove upper shell (see page 10). 2. Remove fan (see page 19).3. Remove fuel and air line hoses from nozzle assem-bly. 4. Turn nozzle assembly 1/4 turn to left and pull towardmotor to remove. 5. Place plastic hex-body into vise and lightly tighten. 6. Carefu...
Page 18 - Pump Rotor
18 099800 Pump Rotor (Procedure if rotor is binding) 1. Remove upper shell (see page 10). 2. Remove filter end cover screws using 5/16" nut-driver. 3. Remove filter end cover and air filters. 4. Remove pump plate screws using 5/16" nut-driver. 5. Remove pump plate.6. Remove rotor, insert, an...
Page 19 - SPECIFICATIONS
19 099800 Fan IMPORTANT: Remove fan from motor shaft beforeremoving motor from heater.The weight of the motorresting on the fan coulddamage the fan pitch. 1. Remove upper shell (see page 10). 2. Use 1/8" allen wrench to loosen setscrew whichholds fan to motor shaft. 3. Slip fan off motor shaft.4...
Page 21 - WHEELS AND HANDLES FOR
21 099800 ASSEMBLY, EURO PFA/PV 018A 1 2 3 4 5 6 7 WHEELS AND HANDLES FOR 90,000 AND 150,000 BTU/Hr MODELS KEY PART PART 90,000 150,000 NO. NUMBER DESCRIPTION QTY. QTY. 1 HA2203 Handles 2 — HA2205 Handles — 2 2 M12345-33 Screw, #10-24 x 1 3/4" 8 8 3 M12342-3 Wheel Support Frame 1 — M12831-3 Whee...
Page 23 - PARTS LIST
23 099800 This list contains replaceable parts used in your heater. When ordering parts,be sure to provide the correct model and serial numbers (from the model plate),then the part number and description of the desired part. PARTS LIST 30,000 BTU/Hr KEY PART PART NO. NUMBER DESCRIPTION QTY. 1 M51104...
Page 28 - ILLUSTRATED
28 099800 1 2 3 4 5 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 9 23 24 25 26 27 28 29 30 31 13 32 9 32 33 34 9 35 36 37 40 41 42 43 9 45 46 47 9 48 44 49 50 51 21 32 52 6 39 38 BURNER HEAD 150 EAI/EBI PFA/P 028 ILLUSTRATED PARTS BREAKDOWN 150,000 BTU/Hr 22-1 22-2 22-3 22-4 22-5 22-6 22-7 22-8 22-9 22...
Page 30 - ACCESSORIES; HEAVY DUTY WHEELS AND; For heavy duty applications.; STANDARD WHEELS AND; Makes heater even more portable and
30 099800 ACCESSORIES Purchase accessories fromyour local dealer. HEAVY DUTY WHEELS AND HANDLE KIT - HA1202 For heavy duty applications. Makes your heater even more portable and convenient. For 30/70,000 BTU/Hr models. AIR GAUGE KIT - HA1180 For all models. Special tool to check pump pressure. STAND...
Page 31 - NOTES
31 099800 NOTES _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ _______________________________________________________________ ____________________________...
Page 32 - WARRANTY AND REPAIR SERVICE; CERTIFICATE OF GENERAL
32 099800 WARRANTY AND REPAIR SERVICE IMPLIED WARRANTIES INCLUDING THOSE OF MER-CHANTABILITY AND FITNESS FOR A PARTICULAR PUR-POSE ARE LIMITED TO THE DURATION OF THIS EX-PRESS WARRANTY. Any transportation charges, costs of installation, duty, taxes or any other charges whatsoever must be borne by th...
