Desa HRC101 - Manual

Desa HRC101 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1

2

3

4

5

6

7

8

Page: / 8 Go to

Next Page

PDF Text Table of Contents

Table of Contents:

• Page 2 – REmotE oPERAtIon; lot before using the hand-held; ing Instructions; in your owner’s; Control Knob and Flame Adjustment; Control Knob; to Lock; Control Unit
• Page 3 – manual mode; Figure 7 - Thermostat Hand-Held Remote Control Unit; Selects AUTO Mode; Safety Features
• Page 4 – DocKIng StAtIon; The wall docking station offers a convenient loca-
• Page 5 – Conser ve este instructivo para referencia futura.; INSTRUCCIONES DE OPERACIÓN PARA LOS MODELOS; Para uso con sistemas para chimenea y juegos de leños de; alimentación con placa, el; Figura 2 - Instalación del receptor; Figura 3 - Conexión de los cables
• Page 6 – Batería de 9 voltios; oPERAcIón REmotA; AvISo: antes de utilizar la unidad; nes de encendido; en el manual; Ahora ya puede encender y apagar el quema; Para bloquearlo; está bloqueado, la luz no se encenderá al presionar; Para desbloquearlo; Luz indicadora
• Page 7 – modo manual; Figura 7 - Unidad de control remoto con termostato; Aspectos de seguridad
• Page 8 – BASE PARA EL contRoL REmoto; Figura 8 - Base para el control remoto

Loading the manual

Save for future reference.

For more information, visit www.desatech.com

WIRELESS HAND-HELD REMOTE CONTROL MODELS HRC100,

HRC101, HRC200 AND HRC201 OPERATING INSTRUCTIONS

For Use With DESA Heating Products Remote Ready Log Sets

and Fireplace Systems

InStALLIng REmotE REcEIvER

1. Disconnect switch wires from the control valve.

Some units will have an on/off switch with

switch plate that is connected to the control

valve. other units will have a jumper wire that

will need to be removed from the control valve

(see figure 1).

2. Remove screws and switch plate as shown in

figure 1. Discard after removing.

3. Install remote receiver unit onto gas log heater

base using clips (2) and insulating washers

provided.

4. Push clips firmly into place (see Figure 2).

5. Connect wires as shown in figure 3.

Note:

On yellow flame models, reuse provided

phillips head screws and reinstall heat shield over

receiving unit.

InStALLIng WIRELESS REmotE
contRoL AccESSoRY

Two 9-volt alkaline batteries (not included) are

required to operate this wireless hand held remote

control set. One battery must be installed in the

receiver and one in the hand-held remote control

unit.

Note:

Only use alkaline batteries.

Installing 9-volt Battery (not Included) in
Receiver

1. Locate the battery clip mounted on the back

of the receiver.

2. Slide a 9-volt battery through the clip.

3. Attach the terminal wires to the battery.

Figure 1 - Disconnecting Wires from

Control Valve

Front

Back

Wires to
Control Valve

Screw

Jumper Wire

Control Valve

Figure 2 - Installing Remote Receiver

Front

Back

Insulating
Washers

Remote
Receiver

Mounting
Clips

Figure 3 - Connecting Wires

Valve

Red Wire
From
Receiver

White
Wire From
Receiver

Battery Clip

ON/OFF Switch with
Switch Plate

Other Desa Models

• Desa CGD3924P
  • User Manual
  • Manual
• Desa WMP10
  • Manual
• Desa R115T
  • Manual
• Desa CCL3018NR
  • Manual
• Desa CCL3924NRA
  • Manual
• Desa CSPBPT CSPINT
  • Manual
• Desa 35
  • Manual
• Desa RP30B
  • Manual
• Desa BLP50VA
  • Manual
• Desa CGP10A
  • Manual