Desa 496 - Manual

6 105635 TOO HARD Pointflattens 482-29 TOO BRITTLE Surfaceshatters 482-30 TOO SOFT Sinks inwithaveragehammerblow 482-28 ? ? ? G 018 G 018 G 018 G 018 Safety Precautions 7. An operator taking medication should take extra precautions while handling thetool. Never drink alcoholic beverages or take medi...

8 105635 TOO THIN WELD 482-40 G 018 3/16" MIN 1/2" 1" 482-41 Safety Precautions 7. Do not drive power fasteners into steel base material less then 3/16" thick,within 2" of a weld, within 1/2" of the edge or within 1" of another power fastener. 3" 3" 3" 482-39 ...

9 105635 POWERLOADS POWERLOADS GASOLINE GAS OLINE 482-50 482-49 ; ; ; G 018 G 018 G 018 G 018 G 018 Safety Precautions 2. Should the tool fail to fire, hold the muzzle firmly against the work surface for30 seconds. Release the trigger and remove pressure on the tool whileholding the muzzle against t...

12 105635 Why A Power Fastener Holds WHY A POWER FASTENER HOLDSIN CONCRETE The compression bond of the concrete to the powerfastener accounts for the majority of the holding power.The fastener displaces the concrete which tries to returnto its original form causing a squeezing effect. Maximum holdin...

13 105635 482-67 OVERDRIVE G 018 Selecting Power Fasteners and Power loads FASTENING INTO CONCRETE The proper power fastener length can be determined byadding the thickness of the material to be fastened and theamount of fastener that will actually penetrate the con-crete. The concrete must be three...

14 105635 Operation 1. Grasp barrel assembly and slide forward rapidly until it stops. Push barrelassembly back into tool to the closed position. This sets piston into firingposition. 4. Place the muzzle of tool perpendicular to work surface without tilting the tool.Push tool against work surface un...

16 105635 Parts List 496 Key Part No. No. Description Qty. 1 502001 Housing 1 2 502100 Outer Liner Assembly 1 3 501104 Push Pin 1 4 301013 Ball Setter 2 5 501106 Spring Ball Set 1 6 501107 Key Stop 1 7 301014 Annular Spring 1 8 502200 Barrel 1 9 502202 Piston Assembly (Includes Ring) 1 10 501212 Rin...

18 105635 Tool Disassembly Figure 2 - Removing Stop Stop A. REMOVING BARREL ASSEMBLY1. Using screwdriver, lift end of annular spring and rotate spring until stop is uncovered (see Figure 1). Annular Spring WARNING: Always unload a powder actuated tool before disassembling,replacing barrel, cleaning,...

21 105635 Tool Assembly WARNING: Always unload a powder actuated tool before disassembling,replacing barrel, cleaning, or assembling. A. INSERTING OUTER LINER ASSEMBLY INTO HOUSING1. Place ball bearing and spring in end of outer liner assembly (see Figure 11, page 20). 2. Slide outer liner assembly ...

24 105635 Troubleshooting Guide Piston hangs outof muzzle. Overdrivenfastener. Piston jammed. Power load strip willnot advance. Reduction or lossof power. Tool does notcompletely depress. Tool does not fire. Opening and clos-ing of barrel orpushing down ontool, etc. is notsmooth but isrough or binds...

25 105635 Parts Centrals Contact authorized dealers of this product. If they can’t supply original replace-ment part(s), either contact your nearest Parts Central (see below) or call DESAInternational’s Parts Department at 1-800-972-7879for information. When calling DESA International, have ready • ...

26 105635 Application Chart 2 1/2"2 1/2"2" 1 1/2"1 1/2"1 1/2" 1"1"1" to this ConcreteCement BlockSteel (3/16" to 3/8" Thick) ConcreteCement BlockSteel (3/16" to 3/8" Thick) ConcreteCement BlockSteel (3/16" to 3/8" Thick) YellowGreenYellow/R...

27 105635 Maintenance Log Date Maintenance Performed

Limited Warranty Agreement DESA International warrants the Remington Power Pro  Model 496 against defects in materials and workmanship for a period of one (1) year from the date of purchase. If within one (1) year from the purchase date this Powder Actuated Tool fails due toa defect in material or ...