Desa 105801-09 - Manual
Desa 105801-09 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – LOG REMOVAL; The new main burner orifice will
- Page 3 – INSTALLATION INSTRUCTIONS; DIRECT VENT DECORATIVE FIREPLACE; CONVERSION INFORMATION LABEL; This appliance was converted on; to; Figure 10 - Conversion Information Label
- Page 4 – NOT A UPC; FINAL PREPARATION; The conversion is now complete.; WARNING: Never use an open
Parts included with this kit:
Part No.
Description
Quantity
Instruction Sheet
1
106040-02
Pilot Orifice
1
104504-02
Burner, Propane/LP
1
104506-02
Main Burner Orifice (1.32mm)
1
105838-02
Gas Valve Regulator
1
105801-09
Conversion Label, English
1
106038-09
Conversion Label, French
1
106080-01
Conversion Information Label
1
Tools Required
• 10mm Open End Wrench
• Torx T20 or Slotted Screwdriver
• 12mm Open End Wrench
• 3/8" Socket or Nut Driver or
• 5/16" Socket or Nut Driver
Slotted Screwdriver
• 18mm Open End Wrench or
• #2 Phillips Screwdriver
Adjustable Wrench
• High Temperature Silicone Sealant
• 3/4" Open End Wrench or
(GE RTV 106/Loctite RTV 81585)
Adjustable Wrench
• Thread Sealant (Resistant to Propane/LP)
• 7/8" Open End Wrench or
Channel Lock Pliers
If any of these pieces are missing or damaged, contact the dealer where you purchased this
kit or DESA International at 1-800-972-7879 for referral information.
INSTALLATION INSTRUCTIONS
FOR PC-BDV37N (02267)
CONVERSION KIT
NATURAL GAS TO PROPANE/LP GAS
For Use When Converting Models BDV37N Series
INTERNATIONAL
This conversion kit must be installed by a qualified service agency.
Read these instructions completely before installing this conversion kit.
Before proceeding, make sure the gas control valve is in the “OFF” position, all electrical
power to the appliance is OFF, and the fireplace is cool to the touch.
CAUTION: The gas supply shall be shut off prior to disconnecting the
electrical power before proceeding with the conversion.
REMOVING GLASS DOOR
1.
Remove the upper louver panel by lift-
ing upward and out (see Figure 1).
2.
Using a 3/8" socket or slotted screw-
driver remove the screws from the three
tabs at the top of the glass door (see
Figure 2, page 2). Hold glass door se-
curely to keep it from falling forward.
3.
Grasp door by both sides and ease it
upward off the lower bracket (see Fig-
ure 2, page 2).
Top Louver Panel
Figure 1 - Removing Top Louver Panel
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
PC-BDV37N (02267) Conversion Kit 2 105822 Screw Glass DoorAssembly Lower Bracket forGlass Door Assembly Figure 2 - Removing/Replacing GlassDoor LOG REMOVAL Carefully remove the log set and embermaterial from around the burner and placethem outside the fireplace. BURNER, MAIN BURNERORIFICE, AND PILOT...
3 105822 INSTALLATION INSTRUCTIONS HI LO O FF PI L O T O N GAS CONTROL VALVECONVERSION Convert the gas control valve by swappingout the valve regulator portion of the gasvalve. 1. Using a TORX T20 or slotted screw-driver, remove and discard the threemounting screws, pressure regulatortower, and diap...
105822-01REV. B09/99 NOT A UPC 105822 01 FINAL PREPARATION 1. Replace logs and embers back into thecorrect positions as instructed in yourappliance Owner’s Manual. 2. Reinstall glass door and upper louverpanel on fireplace. To do so, reverse theinstructions under Removing GlassDoor on page 1. The co...
