Delta SLM100 - Manual

CEILING/WALL VENTILATION FAN

READ AND SAVE THESE INSTRUCTIONS

GENERAL SAFETY INFORMATION

1.

Make sure that the electric service supply voltage is

AC 120V, 60Hz.

2.

Follow all local electrical and safety codes, as well as

the Nation Electrical Code (NEC) and the Occupation

Safety and Health Act (OSH Act).

3.

Always disconnect the power source before working

on or near the ventilating fan, motor or junction box.

4.

Protect the power cord from sharp edges, oil, grease,

hot surfaces, chemicals or other objects.

5.

Do not kink the power cord.

6.

Do not install the unit where ducts are configured as

shown in Fig. A.

7.

Provide suction parts with proper ventilation.

8.

This unit is UL listed for use over a bathtub or shower

when installed in a GFCI protected branch circuit.

9.

These ventilating fans are intended for residential

usage only.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1.

Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

2.

Before servicing or cleaning unit, switch power off at

service panel and lock the service disconnecting

means to prevent power from being switched on

accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent

warning device, such as a tag, to the service panel.

3.

Installation work and electrical wiring must be done

by qualified person(s) in accordance with all
applicable codes and standards, including fire-rated

construction.

4.

Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.

Follow the heating equipment manufacturer’s

guideline and safety standards such as those

published by the National Fire Protection Association
(NFPA), and the American Society for Heating

,

Refrigeration and Air Conditioning Engineers

(ASHRAE) and the local code authorities.

5.

When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

6.

Ducted fans must always be vented to the outdoors.

7.

If this unit is to be installed over a tub or shower, it

must be marked as appropriate for the application

and be connected to a GFCI (Ground Fault Circuit

Interrupter) – protected branch circuit.

8.

Do not use this unit with any other solid-state control

devices. Solid-state control devices may cause

harmonic distortion, which can cause a motor

humming noise.

9.

NEVER

place a switch where it can be reached from a

tub or shower.

10.

Not to be installed in a ceiling thermally insulated to

a value greater than R40. ( This is required for

installation in Canada only).

Turning angle too large

Duct shrink

Too many elbows

Elbow near the body

Body

CAUTION

1.

For general ventilating use only. Do not use to
exhaust hazardous or explosive materials and vapors.

2.

Not for use in cooking areas. (Fig. B)

3.

This product must properly connect to the

grounding conductor of the supply circuit.

4.

To reduce the risk of injury to persons, install the fan

at least 8.2 feet (2.5m) above the floor.

45

C oo k ing a re a

45

D o n o t in s tall a b ov e o r

in s id e th is a rea

C oo k ing

E q uip m e n t

flo or

SUPPLIED ACCESSORIES

Part name

Appearance

Quantity

Grille

1

Motor

1

Housing

1

Duct

Connector

(4”)

1

Screw

(

Ø

4×25)

4

Screw

(

NO.8-32

)

1

Suspension

Bracket

1

3 Inches

Adaptor

Connector

1

1. INSTALLATIONS

Proper insulation around the fan to minimize

building heat loss and gain.

MOUNT HOUSING WITH FLANGE(CELING/ WALL)

1-1. To bend the housing tabs out to 90 degree

and make housing tabs contact the bottom or

front of the joist.

1-2. The housing mounts with 4 screws (

Ø

4×25).

Screw housing to joist through the round

holes in each mounting flange, then through
the other holes.

Fig. A

Fig. B

Page 1.

INSTALLATION AND OPERATING INSTRUCTIONS

MODELS SLM80 / SLM100