Delta 33-830 - Manual - manualsarea.com

Page 2 - GENERAL SAFETY RULES

2 GENERAL SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain hazards involved with the operation of the product. Using the machine with respect and caution willconsiderably lessen the possibility of personal inj...

Page 3 - MINIMUM GAUGE EXTENSION CORD

3 ADDITIONAL SAFETY RULES FOR RADIAL ARM SAWS 1. READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE OPERATING THIS TOOL. 2. DO NOT OPERATE THIS TOOL until it is completely assembled and installed according to the instructions.3. OBTAIN ADVICE from your supervisor, instructor, or some other qualified ...

Page 5 - CHANGING VOLTAGE; OVERLOAD PROTECTION

5 Fig. C GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER Fig. D GROUNDED OUTLET BOX CURRENT CARRYING PRONGS GROUNDING BLADEIS LONGEST OF THE 3 BLADES Fig. E Fig. F CHANGING VOLTAGE The motor supplied with your saw is wired for 120 voltoperation. If you desire to operate your saw at 240 volts,it is neces...

Page 6 - FUNCTIONAL DESCRIPTION; FOREWORD; UNPACKING AND CLEANING; NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT

6 FUNCTIONAL DESCRIPTION FOREWORD Delta Model 33-830 is a 10" (254mm) Professional Radial Arm Saw with maximum cutting capacity of 16" (406mm)crosscut, 2-3/4" (70mm) depth at 90° and 2-1/2" (64mm) depth at 45° bevel. It is designed with positive bevel stops at0°, 45° and 90° and posi...

Page 8 - EXPLANATION OF OPERATING CONTROLS

8 EXPLANATION OF OPERATING CONTROLS The following is an explanation of the operating controls of the Delta 10" Radial Saw. We suggest you study theseexplanations carefully to familiarize yourself with the controls before turning on the power. Doing otherwise may causedamage to the saw or persona...

Page 9 - ASSEMBLY; TOOLS NEEDED FOR ASSEMBLY AND ADJUSTMENT

9 ASSEMBLY TOOLS NEEDED FOR ASSEMBLY AND ADJUSTMENT Your Delta Radial Arm Saw can be assembled and adjusted using a few common hand tools, including: • Phillips head screwdriver • 7/16 ″ Wrench • 1/2 ″ Socket, ratchet, and extension • 3/16 ″ Allen Wrench • Flat blade screwdriver • 1/2 ″ Wrench • Adj...

Page 17 - ADJUSTING IN/OUT RIP SCALE

17 Fig. 41 Fig. 42 Fig. 43 5. Place a square (D) Fig. 41, on the table and against the saw blade, as shown, and check to see if the bladeis square with the table. NOTE: The square should rest between two teeth of the saw blade . 6. If an adjustment is necessary, make certain bevel clamp lever (C) Fi...

Page 19 - FASTENING SAW TO THE FLOOR

19 FASTENING SAW TO THE FLOOR If during operation there is any tendency for the saw to tip over, slide, or walk on the supporting surface, thesaw should be secured to the floor surface through holes provided on the bottom of each leg. Fig. 48 Fig. 49 Fig. 51 Fig. 50 CUTTING INTOTABLE BOARDS 1. Assem...

Page 20 - MOTOR; OPERATING CONTROLS AND ADJUSTMENTS

20 Fig. 62 Fig. 63 ADJUSTING BALLBEARINGS AGAINST TRACK The cutting-head (C) Fig. 61, is suspended from fourpre-loaded, lubricated, shielded ball bearings, two ofwhich are on fixed shafts at (A) , and two on adjustableshafts at (B). NOTE: CUTTING-HEAD (C) FIG. 61, IS REMOVED FROM TRACK ARM FOR ILLUS...

Page 24 - AUXILIARY TABLE BOARD FACING; USING A TABLE EXTENSION; OPERATIONS; MITER CUTTING

CROSS-CUT STOP A block of wood placed at (B) Fig. 74A clamped to thetrack arm with a small “C” clamp will preventunnecessary travel (T) of the cutting-head on the trackarm. This is especially useful when performing repetitiveoperations. Clamp the block of wood to the right side ofthe track arm at a ...

Page 26 - CONSTRUCTING A PUSH STICK; PUSH STICK

26 CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily bemade from scrap material by following the pattern shown in Fig. 79. Fig. 79 PUSH STICK MAKE FROM 1/2 ″ OR 3/4 ″ WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO ...

Page 27 - Two Year Limited Warranty

27 Printed in U.S.A. PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your...

Page 28 - NOTES

Page 29 - DELTA SERVICE CENTERS; CANADIAN PORTER-CABLE

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): BAMMER ® , INNOVATION THAT WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PORTA-PLANE ® , PORTER- CABLE ® , QUICKSAND ® , SANDTRAP ® , SAW BOSS ® , SPEE...

Delta 33-830 - Manual

Table of Contents:

Summary

Other Delta Models