Dashmate DSH-HWK - User Manual

Page 3 - TABLE OF CONTENTS

NOTES AND INSTALLATION .......................................................................................... 4 1 PRODUCT INFORMATION ................................................................................... 5 1.1 INTRODUCTION ..............................................................

Page 4 - NOTES AND INSTALLATION; IMPORTANT: REFER TO YOUR VEHICLE OWNER’S MANUAL

NOTES AND INSTALLATION IMPORTANT: REFER TO YOUR VEHICLE OWNER’S MANUAL TO DETERMINE: • Location of the fuse box • How to access the fuse box • The type of fuse tap required It is highly recommended that you have a quick read of the installation instructions in this user guide. If you are not comfort...

Page 5 - PRODUCT INFORMATION; Provides constant power to your dashcam when your vehicle is

1 PRODUCT INFORMATION Get constant power for your dashcam. DSH-HWK connects to your vehicle battery through your vehicle’s fuse box and provides constant power to your dashcam when the engine is turned off. It includes several fuse tap options that suit most vehicles* and your dashcam connects to th...

Page 7 - Cable Ties x 4; BATTERY DRAIN PROTECTION; For 12V Batteries; For 24V Batteries; V recommended for most users in general driving conditions.

1.3 PACKAGE CONTENTS CONT’D ACCESSORIES 1. Cable Ties x 4 2 BATTERY DRAIN PROTECTION The Hardwire Kit will protect your dashcam from draining your vehicle’s battery. If your vehicle’s battery voltage gets too low, DSH-HWK will stop powering your camera to save power. You will never have to worry abo...

Page 8 - Using a 50Wh lead acid battery for an example, the 25% consumption; Temperature

2.2 VEHICLE BATTERY LEAD ACID STATES AND CAPACITY Use the below table to assist in determining your desired voltage cut off level for battery drain protection. For example if the temperature is 38°C and you want to keep a 75% lead acid state capacity remaining in your battery when the hardwire kit c...

Page 9 - INSTALLATION; and should be used as a guide only for a DIY installation. To ensure; There are 2 main stages in the hardwire kit installation; NOTE: Determine the location of your vehicle’s fuse box before

3 INSTALLATION The location of the vehicle’s fuse box varies from vehicle make and model. Locations may include underneath the driver’s side dashboard, behind the glove box and underneath the central console. Where in doubt, always refer to your vehicle owner’s manual to determine the location of th...

Page 10 - CONNECTING HARDWIRE KIT TO YOUR DASHCAM; IMPORTANT: Refer to your dashcam owner’s manual for initial; Two dashcam connector cables are included with DSH-HWK – one; ROUTING THE OUTPUT CABLE FROM THE DASHCAM; NOTE: You may need to consult your vehicle manufacturer for

3.1 CONNECTING HARDWIRE KIT TO YOUR DASHCAM IMPORTANT: Refer to your dashcam owner’s manual for initial installation of your dashcam in your vehicle. 3.1.1 ATTACHING THE USB CONNECTOR TO THE DASHCAM 1. Two dashcam connector cables are included with DSH-HWK – one with a Mini USB plug and one with a M...

Page 11 - INSTALLING THE OUTPUT CABLES IN VEHICLE

3.2 ROUTING THE OUTPUT CABLE FROM THE DASHCAM TO THE FUSE BOX CONT’D 3.2.1 INSTALLING THE OUTPUT CABLES IN VEHICLE 1. Once the USB connector cable is attached to your dashcam, it then needs to be connected to the hardwire kit’s output cable. (Fig 5) 2. The hardwire kit output cable will then need to...

Page 12 - INSTALLING THE OUTPUT CABLES IN VEHICLE CONT’D

3.2 ROUTING THE OUTPUT CABLE FROM THE DASHCAM TO THE FUSE BOX CONT’D 3.2.1 INSTALLING THE OUTPUT CABLES IN VEHICLE CONT’D FIG. 7 FIG. 6b FIG. 8 12

Page 16 - NOTE: Refer to your vehicle’s fuse layout panel to determine the

3.2 CONNECTING HARDWIRE KIT TO YOUR FUSE BOX AND GROUNDING 3.3.1 CONNECTING TO THE FUSE BOX NOTE: Refer to your vehicle’s fuse layout panel to determine the permanent power fuse for constant power feed. The fuse cable needs to be connected to the 12V/24V battery feed. 1. Determine the fuse tap cable...

Page 18 - mounted to the chassis of the vehicle or any metal part of the; NOTE: The black earth cable needs to be connected to the vehicle

3.2 CONNECTING HARDWIRE KIT TO YOUR FUSE BOX AND GROUNDING CONT’D 3.3.2 CONNECTING TO GROUND 1. Locate earth terminal/bolt or any vehicle bolt accessible that is mounted to the chassis of the vehicle or any metal part of the vehicle - located near the vehicle fuse box (Fig (17). 2. Feed black input ...

Page 20 - WARRANTY TERMS & CONDITIONS

5 WARRANTY TERMS & CONDITIONS Our goods come with guarantees that cannot be excluded under the Australian & New Zealand Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitle...

Page 21 - NOTES

Dashmate DSH-HWK - User Manual

Table of Contents:

Summary

Other Dashmate Dashcams Models