D-Link DPH-50U - Manual - manualsarea.com

Page 2 - TABLE OF CONTENTS; IP

TABLE OF CONTENTS 1. INTRODUCTION ........................................................................................ 3 2. PACKAGE CONTENTS ............................................................................. 4 3. REQUIREMENTS...............................................................

Page 6 - Verify the installation is OK (step 3 below)

4. DPH-50U Installation DO NOT CONNECT THE DPH-50U VoIP USB Phone Adapter TO YOUR COMPUTER UNTIL INSTRUCTED TO DO SO BY THE DPH-50U INSTALLATION WIZARD The following instructions will guide you to through the process of installing the DPH-50U VoIP USB Phone Adapter. The installation procedure is to:...

Page 7 - installation should start automatically. Please press “; Install Utility

STEP 2: Insert the supplied CD-ROM into your PC CD-ROM drive. The installation should start automatically. Please press “ Install Utility ” You will see the following popup. Press Yes to proceed or No to cancel.

Page 9 - New Hardware Found Wizard

The other end of the USB cable must be connected to a USB port on your computer as shown below, or to an AC Powered USB hub. The D-Link USB Phone Adapter MUST not be connected to a bus powered USB hub. You will see the following Windows New Hardware Found Wizard . Connect PC Connect NB

Page 10 - Next; When you see the following screen, press the; Finish

Select Install the software automatically (Recommended) and press the Next button. The installation will continue and you will see the following screen. When you see the following screen, press the Finish button.

Page 12 - Continue Anyway; allow this program; OK

When you see the following screen, press the Continue Anyway button. When you will see the following screen, select the option, “ allow this program to use Skype” and press the OK button. When you see the following screen, press the Finish button.

Page 13 - When the installation completes you should see the following

STEP 3: When the installation completes you should see the following message appear near your system tray and a new telephone icon (circled in red below) in your system tray as shown below. The telephone icon indicates that the DPH-50U software is installed and running and that you can start making ...

Page 14 - Connect a standard telephone handset to the DPH-50U; phone; jack; line; jack and a

STEP 4: Connect a standard telephone handset to the DPH-50U phone jack using a telephone cable as shown below STEP 5: Connect a telephone cable between the DPH-50U line jack and a wall jack as shown below. Note that this is only required for making regular phone calls or for forwarding Skype calls t...

Page 22 - Making and Receiving Calls; telephone number; Setting Up Skype Speed Dial

7. Making and Receiving Calls You can continue to use the telephone handset connected to the DPH-50U VoIP USB Phone Adapter to make and receive standard telephone calls as you used without any change. To make a standard phone call, just pick up the handset and dial as you normally would. To answer (...

Page 24 - You will now see an indication that the SkypeTM contact has a speed

Step 3: You will now see an indication that the Skype™ contact has a speed dial associated with them as shown below.

Page 25 - to put the current call; Forwarding Calls

7.2 Switching Between VoIP and Regular Calls While on a regular phone call you may receive a Skype™ call or while on a Skype™ call you may receive a regular call. The DPH-50U will indicate an incoming call with an audible tone and you can switch between the two and back and forth by pressing #1. Whi...

Page 27 - button as shown below. Enter the

Select the number of rings before the forwarding takes place as shown below. Then select the telephone that should be dialed on the telephone line and press the Apply and/or Exit button as shown below. Enter the telephone exactly as you would dial it if you were to pick up a telephone directly conne...

Page 35 - THE DPH-50U STORES FILES TO YOUR

Recording is controlled by two mechanisms: automatic and manual. Manual recording has two modes: Through the Call Recorder screen above - controlled by pressing the record (red dot) and stop (black square) buttons. From the telephone handset – controlled by pressing the #7 keys (start recording) and...

Page 36 - Changing the Default Settings; Initiate Voip Call; – press these keys to get a VoIP dial-tone. You can; Send Ke; y – press this key following the phone number (or speed dial; Call Waiting Sequence; – press these keys during a call to switch; Conference Key Sequence; – while on a Skype call and you receive a

7.8 Changing the Default Settings You can change the default settings for sending a call, activating a Skype™ call, switching between a Skype™ call and a regular call (call waiting) and conference calling, by running the DPH-50U configuration. Right click on the DPH-50U and select Configure as shown...

Page 37 - Restore Defaults; button if you want to restore all sequences to

Press the Restore Defaults button if you want to restore all sequences to their factory shipped settings.

Page 40 - Installing a New Version

10. Installing a New Version When you install a new version of DPH-50U software, at the end you will see a slightly different Skype warning message as shown below. Select “Allow this program to use Skype” and press OK as shown below:

Page 41 - Q2. Wrong Device Installed

11. Troubleshooting The first step in troubleshooting is to read the readme.txt that appears in the DPH-50U program group. It contains a list of known issues for the current DP-50U driver version. To find out the driver version, right click on the DPH-50U (green telephone in the system tray) and sel...

Page 42 - Q5. Cannot hear the SkypeTM call in telephone handset

and install the adapter properly. Q3. DPH-50U does not appear to be responding to incoming calls There are several reasons why DPH-50U may not function. • DPH-50U may not work properly with some 4 wire (multiline) phones • Make sure the DPH-50U is connected to the PC and DPH-50U software is running ...

Page 43 - Q6. Call Forwarding is not working properly; Make sure that a telephone cable is plugged into the DPH-50U; jack and to the wall phone plug

and then select Sound Devices as shown below. Check the Audio In and Audio Out list boxes and make sure D-Link Virtual Audio device is selected. Q6. Call Forwarding is not working properly • Make sure that a telephone cable is plugged into the DPH-50U line jack and to the wall phone plug • Try to di...

D-Link DPH-50U - Manual

Table of Contents:

Summary

Other D-Link Models