Craftsman 137.248840 User Manual

Page 2 - ONE-YEAR FULL WARRANTY ON CRAFTSMAN TOOL; PRODUCT SPECIFICATION

TABLE OF COriTE SECTION PAGE Warranty............................................................. 2 Product Specifications.............................................. 2Power Tool Safety .............................................. 3 Table Saw Safety.................................................

Page 3 - POWER TOOL SAP

POWER TOOL SAP A WARNING Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious Injury or damage to the table saw. Good safety practices are a combination of common sense, staying alert and understanding how ...

Page 4 - ABLE SAW SAFETY

1 ABLE SAW SAFETY 1. ALWAYS USE SAW BLADE GUARD, splitter and anti-kickback pawls for every operation for which they can be used, including through-sawing. Through-sawing operations are those in which the blade cuts completely through the workpiece when ripping or cross-cutting. 2 . 3. 4. 5. ALWAYS ...

Page 5 - ELECTRICAL REQUIREMENTS AND SAP

ELECTRICAL REQUIREMENTS AND SAP GROUNDING INSTRUCTIONS IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least resistance for electric currents and reduces the risk of electric shock. This tool is equipped with an electrical cord that has an equipment-grounding conductor and a...

Page 6 - I I M I I I I M I

ACCESSORIES AND ATTACHMENTS CARTON CONTENT RECOMMENDED ACCESSORIES A WARNING Visit your Sears Hardware Department or see the Sears Power and Hand Too! Catalog to purchase recommended accessories for this power tool. A WARNING To avoid the risk of personal injury, do not modify this power tool or use...

Page 8 - KNOW YOUR TABLE

Page 9 - GLOSSARY OF TERM

GLOSSARY OF TERM ANTI-KICKBACK PAWLS - Prevents the work piece from being kicked upward or back toward the front of the table saw by the spinning blade. ARBOR - The shaft on which the blade or dado is mounted. BE¥EL CUT - An angle cut made through the face of the work piece. BLADE BEVEL SCALE - Meas...

Page 11 - I V

MOUNT SAW ON WORK SURFACE (FIG. C) 1. If the leg set will not be used, the saw must be properly secured to a sturdy workbench using the four mounting holes at the base of the saw. 2. The surface of the table where the saw is to be mounted must have a hole large enough to facilitate sawdust fall-thro...

Page 17 - OPERATION

OPERATION BASIC SAW OPERATIONS RAISE THE BLADE (FIG. W) To raise or lower the blade, turn the blade elevation handwheel (1) to the desired blade height, and then tighten lock handle (2) to maintain the desired blade angle. Fig. W 1 TILTING THE BLADE (FIG. W) 1. To tilt the saw blade for bevel cuttin...

Page 22 - MAIMTENANC

MAIMTENANC GENERAL MAINTENANCE Fig. LL A WARNING For your own safety, turn the switch OFF and remove the switch key. Remove the plug from the power source outlet before maintaining or lubricating your saw. 1. Clean out all sawdust that has accumulated inside the saw cabinet and the motor. 2. Polish ...

Page 23 - JJ; ROUBLESHOOTING QUID

JJ ROUBLESHOOTING QUID A WARNING To avoid injury from an accidental start, turn the switch “OFF” and always remove the plug from the power source before making any adjustments. • Consult your local Sears Service Center if for any reason the motor wii not run. SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTIO...

Page 24 - PARTS LIS

PARTS LIS 10 in. TABLE SAW MODEL NO. 137.248840 A WARNING When servicing use only CRAFTSMAN replacement parts. Use of any other parts many create a HAZARD or cause product damage. Any attempt to repair or replace electrical parts on this Table Saw may create a HAZARD unless repair is done by a quali...

Page 30 - IJ; Your Home

I fi IJ Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and Operator’s Manuals that you need to do-it-yourself. For Sears professional ...