Page 3 - Claims
Intimidator™ Spot LED 350 User Manual (Rev. 02) Page 3 of 26 1. B EFORE Y OU B EGIN What Is Included 1 x Intimidator™ Spot LED 350 1 x Power Cord 1 x Warranty Card 1 x Quick Reference Guide Unpacking Instructions Immediately upon receipt, carefully unpack the product and check the container ...
Page 5 - NTRODUCTION; Product Overview
Intimidator™ Spot LED 350 User Manual (Rev. 02) Page 5 of 26 2. I NTRODUCTION Product Overview Control Panel and Button Menu DMX Out Safety Loop Fuse Holder DMX In Power In Power Out
Page 6 - Product Dimensions
Page 6 of 26 Intimidator™ Spot LED 350 User Manual (Rev. 02) Product Dimensions
Page 7 - ETUP; AC Power; electrocution or fire.; Fuse; Spare fuse holder
Intimidator™ Spot LED 350 User Manual (Rev. 02) Page 7 of 26 3. S ETUP AC Power The Intimidator™ Spot LED 350 has an auto-ranging power supply and it can work with an input voltage range of 100~240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wirin...
Page 8 - Power Linking; IntimidatorTM Spot LED 350 units on 230 VAC.; Product; Product; Product
Page 8 of 26 Intimidator™ Spot LED 350 User Manual (Rev. 02) Power Linking The product provides power linking via the IEC outlet located in the back of the unit. Please see the diagram below for further explanation. Power Linking Diagram You can power link up to 3 Intimidator™ Spot LED 350 units on ...
Page 9 - Mounting; Orientation; Mounting Diagram; Safety Loop
Intimidator™ Spot LED 350 User Manual (Rev. 02) Page 9 of 26 Mounting Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes section (page 2 of this manual). Orientation The Intimidator™ Spot LED 350 may be mounted in any position; however, make sure ad...
Page 10 - PERATION; Control Panel; Menu Map
Page 10 of 26 Intimidator™ Spot LED 350 User Manual (Rev. 02) 4. O PERATION Control Panel Operation To access the control panel functions, use the four buttons located underneath the display. Please refer to the Product Overview to see the button locations on the control panel. Button Function <M...
Page 11 - Configuration; Starting Address; DMX
Intimidator™ Spot LED 350 User Manual (Rev. 02) Page 11 of 26 Configuration (DMX) Set the product in DMX mode to control with a DMX controller. 1. Connect the product to a suitable power outlet. 2. Turn the product on. 3. Connect a DMX cable from the DMX output of the DMX controller to the DMX input...
Page 12 - DMX Channel Assignments and Values; Channel
Page 12 of 26 Intimidator™ Spot LED 350 User Manual (Rev. 02) DMX Channel Assignments and Values 14-CH Channel Function Value Setting 1 Pan 000 255 0-540° 2 Fine Pan 000 255 Fine control of panning 3 Tilt 000 255 0-270° 4 Fine Tilt 000 255 Fine control of tilting 5 Speed 000 255 Pan/Tilt s...
Page 15 - signals from the controller.; Sound Active; NStS; Automatic Mode; NASl
Intimidator™ Spot LED 350 User Manual (Rev. 02) Page 15 of 26 Configuration (Standalone) Set the product in one of the standalone modes to control without a DMX controller. 1. Connect the product to a suitable power outlet. 2. Turn the product on. Never connect a product that is operating in any sta...
Page 17 - Mode; SLAv; Do not connect more than 31 slave units to the master unit.
Intimidator™ Spot LED 350 User Manual (Rev. 02) Page 17 of 26 Master/Slave Mode The Master/Slave mode allows a single Intimidator™ Spot LED 350 unit (the “master”) to control the actions of one or more Intimidator™ Spot LED 350 units (the “slaves”) without the need of a DMX controller. The master un...
Page 18 - Miscellaneous Operations; Reset Software
Page 18 of 26 Intimidator™ Spot LED 350 User Manual (Rev. 02) Miscellaneous Operations Reset Software To reset the software on the Intimidator™ Spot LED 350, do the following: 1. Press <MODE/ESC> repeatedly until rESt shows on the display. 2. Press <ENTER>. The product will reset all set...
Page 20 - General Troubleshooting; CHAUVET® Technical Support.
Page 20 of 26 Intimidator™ Spot LED 350 User Manual (Rev. 02) General Troubleshooting Symptom Possible Cause Possible Action Circuit breaker or fuse keeps blowing Excessive load on the circuit Make sure that the total load does not exceed 80% of the breaker or fuse nominal current Short circui...
Page 21 - them. Visit our Web site for contact details.
Intimidator™ Spot LED 350 User Manual (Rev. 02) Page 21 of 26 Contact Procedure In case you need to return a product or request support, follow the procedure below: If you live in the US, contact CHAUVET® World Headquarters (see below). If you live in the UK or Ireland, contact CHAUVET® Europe L...
Page 22 - Introduction; The Physical Medium; The Signals
Page 22 of 26 Intimidator™ Spot LED 350 User Manual (Rev. 02) DMX Primer Introduction The DMX protocol (USITT DMX512-A) is a networking protocol that enables a universal DMX controller device to control the features of multiple DMX compatible fixtures, whether PAR cans, wash lights, moving heads, fo...
Page 23 - Personalities; DMX Connectivity; Fixture Location
Intimidator™ Spot LED 350 User Manual (Rev. 02) Page 23 of 26 DMX Configuration The DMX fixture configuration consists in determining how many channels each fixture will need as well as assigning the corresponding DMX channels to each fixture in order to size correctly the DMX controller. Personalit...
Page 25 - could form, which may cause the fixture to perform erratically.; Conversion Chart; DMX Connection
Intimidator™ Spot LED 350 User Manual (Rev. 02) Page 25 of 26 (DMX Connectivity cont.) Test all DMX cables with an ohmmeter to verify their correct polarity and to make sure that there are no short-circuits between any of the pins, or between any pin and ground. If the common wire (shield) touches t...
