Cecilware BC302-IT - Manual

Page 2 - optional; MECHANICAL SPECIFICATIONS; RECOMMENDED COFFEE AMOUNT FOR BREWING

2 SPECIFICATIONS ELECTRICAL SPECIFICATIONS MODEL NO. BC301-IT BC2-IT BC302-IT Volts 120/240 120/240 120/240 Watts 4100 6200 6200 Amps 18 27 27 Wall Outlet (Receptacle) Power Cord CE202 – 30A optional 6-20R 6-30R 6-30R All Brew Centers are single phase with 3 wires plus a ground with cord and plug, e...

Page 3 - operation and aid in identifying potential problems.

3 FEATURES AND BENEFITS OF THE DIGITAL, MEMBRANE CONTROL TOUCH PAD BREWER 1. 100% Solid State Control for improved reliability. 2. Modular design and reduced component count for ease of service. 3. Optional Low Water Temperature Lockout to prevent dispensing at water temperatures below an adjustable...

Page 4 - INSTALLATION AND OPERATING INSTRUCTIONS

4 INSTALLATION AND OPERATING INSTRUCTIONS Warranty is void if the Brewer is connected to any Voltage other than the Voltage specified on the data label of the Brewer. UNPACKING AND INSPECTION Carefully unpack the Brewer by cutting the straps and lifting the carton off the Brewer. ASSEMBLY AND SET-UP...

Page 6 - MODES OF OPERATION – DESCRIPTIONS; Initialization Mode:; Filling State; Waiting State

6 MODES OF OPERATION – DESCRIPTIONS Initialization Mode: The following screen signifies the presence of this mode: CECILWARE &&&&& REV #.# Description – This mode is active only during the first few seconds after “power-on”. The purpose of the Initialization Screen is to identify...

Page 7 - Brewing State; BREWING DDD K; Brew Fill Constant Calibration State; Description; Dilution Fill Constant Calibration State; Description –; Description –

7 Brewing State BREWING DDD K MM:SS HH:MMP Description – This screen is displayed when a Brew Cycle is in progress. The time remaining in the Brew Cycle is displayed in the lower left-hand corner of the screen (depicted as “MM:SS”). The Brew Key LED will blink in this state. The Main Warmer is autom...

Page 8 - SERVICE MODE

8 SERVICE MODE Description – The main function of Service Mode is to give qualified personnel the ability to configure the system to meet the requirements of each installation. General Conventions (unless otherwise indicated) 1) To enter or exit Service Mode simultaneously depress both the hidden ke...

Page 12 - ERROR MODE

12 ERROR MODE Description – The main function of Error Mode is report any system malfunctions and to disable the unit The system must be “powered down” using the Power Key located on the membrane keypad to reset any reported error KEYPAD ! SYSTEM ERROR ! KEYPAD Description – This screen is displayed...

Page 13 - PARTS IDENTIFICATION; DESCRIPTION; OPTIONAL

13 PARTS IDENTIFICATION BC301-IT BC2-IT BC302-IT ITEM P/N QTY P/N QTY DESCRIPTION 1 SF26A 1 SB49A 1 CABINET TOP COVER 2 ---- NG35A NG37A -- 1 1 --- NG40A NG36A NG39A -- 1 1 1 TOUCH PAD LABEL: BC1-IT /BC2-IT BC301-IT / BC302-IT BC120-IT 3 DO42A 1 D042A 2 FAUCET, HOT WATER 4 SF28A 1 SB66A 1 FRONT COVE...

Page 14 - TOP CABIN - PARTS IDENTIFICATION; ITEM; TOP CABIN OPEN VIEW BC302-IT

14 TOP CABIN - PARTS IDENTIFICATION ITEM P/N BC301-IT QTY P/N BC2-IT BC302-IT QTY DESCRIPTION 1 L656A 1 L656A 2 HI-LIMIT 2 L671A 1 L671A 1 THERMISTER PROBE 3 K355Q 1 K355Q 1 WATER LEVEL CONTROL PROBE 4 L688A 1 L688A 2 DINSPENSE VALVE, SINGLE 5 L689A 1 L689A 1 DINSPENSE VALVE, DUAL, BYPASS 6 CH87A 1 ...

Page 15 - TOP CABIN OPEN VIEW BC301-IT

15 BOTTOM CABIN OPEN VIEW BOTTOM CABIN - PARTS IDENTIFICATION ITEM P/N BC301-IT QTY P/N BC2-IT BC302-IT QTY DESCRIPTION 1 L069A 1 L069A 1 POWER SWITCH 2 CD257 1 CD257 1 WATER INLET VALVE 3 B083A 1 B083A 1 TERMINAL BLOCK 4 CE202 1 CE202 1 POWER CORD 5 C396Q 1 C396Q 1 FUSE HOLDER ASS’Y 6 L615A 1 L615A...

Page 16 - CLEANING AND SANITIZING; To prepare a sanitizing solution:; FRONT VIEW – BC301-IT

16 CLEANING AND SANITIZING SANITIZING: All food dispensing units should be sanitized periodically. All parts to be sanitized must be cleaned first. To prepare a sanitizing solution: ADD 2 TSP. OF LIQUID CLOROX BLEACH (5.25% CONCENTRATION) TO 1 GALLON OF WATER AT ROOM TEMPERATURE (70°- 90°F). Note: A...

Page 17 - TROUBLESHOOTING GUIDE; PROBLEM

17 TROUBLESHOOTING GUIDE WARNING: To reduce the risk of electrical shock unplug the dispenser power cord before repairing or replacing any internal components of the unit.. Before any attempt to replace a component be sure to check all electrical connections for proper contact PROBLEM PROBABLE CAUSE...

Page 18 - SPECIAL COMPONENTS TEST AND ADJUSTMENTS

18 SPECIAL COMPONENTS TEST AND ADJUSTMENTS 1) WATER INLET VALVE (SOLENOID) TEST ( Located inside bottom cabin ) Turn power off from touchpad. If the water level rises inside the tank, and shoots out of the overflow, the Water Inlet Valve is leaking. Disconnect wires from the Water Inlet Valve coil a...

Page 19 - SINGLE DISPENSE VALVE; brew; DOUBLE/ DILUTION DISPENSE; both sides

19 5) CHECK DISPENSE VALVES FOR LIME BUILD-UP ( Located inside top cabin ) Drain The Water Tank To Just Below The Level Of The Dispense Valves. Remove The Valves And Clean. You Can Take These Valves Apart By Hand As Shown. Replace The Assembly As Needed. Replace The Valve Into The Tank And Refill ta...

Page 20 - CECILWARE CORPORATION

20 120VAC T1 CH82A 2+ 1- THERMISTOR L617A SEE DETAIL-1 275V 0.1uf C1 HEATER TANK 3KW MT1 G SP1 SWITCH S1 POWER MT2 PROBE LEVEL OVER-FLOW HOSE SAFETY RELAY L553A K2 4 K1 3 WARMER 100W #4 #3 #2 DILUTION SOLENOID DUMP VALVE 8VAC FUSE 6 AMP CONTROL BOARD L669A HI-LIMIT B190A 3 1 2 4 SAFETY RELAY 15 16 1...

Cecilware BC302-IT - Manual

Table of Contents:

Summary

Other Cecilware Models