Page 2 - PROOF OF PURCHASE; Stealth; do not return this product to the
THIS WARRANTY SUPERSEDES ALL PREVIOUS WARRANTIES PROOF OF PURCHASE Retain this information for future reference. Serial number Model number Retailer Date of purchase Date of Product Registration (mailed card or completed online) Stealth ® DC If purchased from our authorized dealer, this ceiling fan ...
Page 3 - tealth; Owner’s Manual; READ AND SAVE THESE INSTRUCTIONS!; Control Installation and Operation
1 P/N C4543001-DC 0211 Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner’s manual completely and carefully. Retain this manual for f...
Page 4 - Parts List
P arts L ist If you are in need of service parts, do not return this fan to the store. 222 6 8 5 9 10 3 4 7 12 11 1 20 21 Parts List Model # C45G11B C45G695B C45G45B Asm. Dwg. # G1173-01 G1173-02 G1173-03 Finish Snow White Alpha Bronze Brushed Nickel Item # Item Name Qnty Part # Part # Part # 1 Ceil...
Page 6 - RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION!; Proper Parts Handling; If the fan does not work:; MODEL C45GxxxB; xxxB
4 Motor Identification Plate RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION! Please take a moment to locate the model number and serial number from your fan (see below) and record this information on the Warranty page inside the front cover of your Owner’s Manual if it does not appear there alr...
Page 7 - INTRODUCTION; BEFORE YOU START
5 s teaLth ® dc Circuit Breaker(Trip breaker for thecircuit you will beworking on) Fuse Box(Remove fuse for thecircuit you will beworking on) SAFE USE • CAUTION: RISK OF ELECTRICAL SHOCK! Installation is to be in accordance with the National Electrical Code, ANSI/NFPA 70-1999 and local codes. If you...
Page 9 - MOUNTING BRACKET INSTALLATION; FAN INSTALLATION; Step 1. Thread the lead wires from the outlet box
7 s teaLth ® dc Using Existing Ceiling Fixture Outlet BoxAfter turning the power OFF at its source (either the circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure it is marked “Approved for Ceiling Fan Mounting.” If it is not...
Page 10 - Step 1. Place a flat washer on each of the two; Step 3. Install the lag screw if needed. Pass the
8 MOUNTING BRACKET INSTALLATION (CONT.) Step 1. Place a flat washer on each of the two screws that came with the outlet box and pass the screws through the slotted holes in the ceiling plate into the screw holes in the outlet box.Step 2. Tighten the screws into the outlet box; do not use lubricants ...
Page 11 - HANGING HARDWARE; Prepare for fan installation as follows:
9 s teaLth ® dc CANOPY HARDWARE CANOPY INSTALLATION Canopy Canopy Hatch Canopy Screws and (4) Lock Washers Phillips Screwdriver LockWasher Canopy Screw Canopy Step 1. Attach the canopy to the ceiling plate with three of the 8-32 x 2 1 / 2 " long canopy screws and lock washers provided with your ...
Page 13 - CANOPY ELECTRICAL CONNECTIONS
11 s teaLth ® dc MOTOR HOUSING ASSEMBLY HANGING THE FAN Step 1. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening as in Figure #1. Check that no wires are pinched. Rotate the fan body until the slot in the ball fits into the pin opposite the can...
Page 14 - BLADE HARDWARE; CANOPY HATCH INSTALLATION; FIGURE 1; ATTACHING THE BLADES; BLADE TIP INSTALLATION:
12 BLADE HARDWARE Screw Driver Step 1. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening.Step 2. Install the canopy hatch with the last canopy screw and lock washer us...
Page 15 - INDENTATION; CONTROL INSTALLATION AND OPERATION; CONTROL BATTERY INSTALLATION
13 s teaLth ® dc BULB INSTALLATION Step 1. Screw the 100-watt Halogen bulb into the socket. Figure 1. Do not touch the glass bulb with your fingers–it is extremely important that the glass be clean. If it is touched, or dirty, clean carefully with a tissue. A dirty glass bulb will cause the bulb to ...
Page 16 - DC Control; CONTROL HOLSTER INSTALLATION; You will have to change the dip switch settings in the remote if
14 DC Control CONTROL HOLSTER INSTALLATION Step 1. Locate a 2x4 wall stud in a convenient location.Step 1. Orient the control bracket as shown over the 2x4 stud.Step 1. Use the provided screws in the mounting holes. Install and tighten screws by hand only. CHANGING FREQUENCY SETTING You will have to...
Page 17 - OPERATION SPEED CONTROL; OPERATION LIGHTS
15 DC Control OPERATION SPEED CONTROL There are six individual speed settings for the fan. Each speed is indicated by the number on the controller. To properly calibrate all speeds of the motor, run the fan on speed "6" for 90 seconds after each AC power reset. To select the desired fan spee...
Page 18 - TROUBLESHOOTING TIPS
16 DC Control Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. TROUBLESHOOTING TIPS This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, an...
Page 19 - PRODUCT SPECIFICATIONS
17 s teaLth ® dc PRODUCT SPECIFICATIONS Model Name: Stealth ® DC Model Number: C45GxxxB Dimensions: A = 10.8" B = 13.25" C = 3" D = 11.5" E = 5.6" Weight: 33 lbs. Motor: DC Blade Span: 54" Blade Iron Pitch: 14° No. of Blades: 5 Technology: DC Control Lightbulb: (1) 100-watt h...