Casablanca C45GxxxB - Manuals

4 Motor Identification Plate RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION! Please take a moment to locate the model number and serial number from your fan (see below) and record this information on the Warranty page inside the front cover of your Owner’s Manual if it does not appear there alr...

5 s teaLth ® dc Circuit Breaker(Trip breaker for thecircuit you will beworking on) Fuse Box(Remove fuse for thecircuit you will beworking on) SAFE USE • CAUTION: RISK OF ELECTRICAL SHOCK! Installation is to be in accordance with the National Electrical Code, ANSI/NFPA 70-1999 and local codes. If you...

7 s teaLth ® dc Using Existing Ceiling Fixture Outlet BoxAfter turning the power OFF at its source (either the circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure it is marked “Approved for Ceiling Fan Mounting.” If it is not...

8 MOUNTING BRACKET INSTALLATION (CONT.) Step 1. Place a flat washer on each of the two screws that came with the outlet box and pass the screws through the slotted holes in the ceiling plate into the screw holes in the outlet box.Step 2. Tighten the screws into the outlet box; do not use lubricants ...

9 s teaLth ® dc CANOPY HARDWARE CANOPY INSTALLATION Canopy Canopy Hatch Canopy Screws and (4) Lock Washers Phillips Screwdriver LockWasher Canopy Screw Canopy Step 1. Attach the canopy to the ceiling plate with three of the 8-32 x 2 1 / 2 " long canopy screws and lock washers provided with your ...

11 s teaLth ® dc MOTOR HOUSING ASSEMBLY HANGING THE FAN Step 1. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening as in Figure #1. Check that no wires are pinched. Rotate the fan body until the slot in the ball fits into the pin opposite the can...

12 BLADE HARDWARE Screw Driver Step 1. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening.Step 2. Install the canopy hatch with the last canopy screw and lock washer us...

13 s teaLth ® dc BULB INSTALLATION Step 1. Screw the 100-watt Halogen bulb into the socket. Figure 1. Do not touch the glass bulb with your fingers–it is extremely important that the glass be clean. If it is touched, or dirty, clean carefully with a tissue. A dirty glass bulb will cause the bulb to ...

14 DC Control CONTROL HOLSTER INSTALLATION Step 1. Locate a 2x4 wall stud in a convenient location.Step 1. Orient the control bracket as shown over the 2x4 stud.Step 1. Use the provided screws in the mounting holes. Install and tighten screws by hand only. CHANGING FREQUENCY SETTING You will have to...

15 DC Control OPERATION SPEED CONTROL There are six individual speed settings for the fan. Each speed is indicated by the number on the controller. To properly calibrate all speeds of the motor, run the fan on speed "6" for 90 seconds after each AC power reset. To select the desired fan spee...

16 DC Control Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. TROUBLESHOOTING TIPS This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, an...

17 s teaLth ® dc PRODUCT SPECIFICATIONS Model Name: Stealth ® DC Model Number: C45GxxxB Dimensions: A = 10.8" B = 13.25" C = 3" D = 11.5" E = 5.6" Weight: 33 lbs. Motor: DC Blade Span: 54" Blade Iron Pitch: 14° No. of Blades: 5 Technology: DC Control Lightbulb: (1) 100-watt h...