Bushnell 98-2293/05-12 - Manual

9 uSing ThE MiL doT RETiCLE FoR RAnging The Equations: Size of target in yards X 1000 = Range in Yards Size of Target in Mils Size of target in inches X 27.778 = Range in Yards Size of target in Mils Size of target in inches X 25.4 = Range in Meters Size of target in Mils Example 1: Looking through ...

10 Example 2: Take the same size target but now the Mil reading is .75 (from crosshair intersection to bottom of first Mil Dot). Known size of target: 12”x 12”Mil Reading: .75 Mil 12 X 27.778 .75 Mil ConvERTing TRAjECToRy dATA To MiL hoLdovERS To calculate holdovers you must first obtain your round’...

11 = Holdover Trajectory Mil Size at given Distance FEdERAL .308 168-gR BThP hoLdovERS FoR A MiL-doT RETiCLE distance Trajectory 1 Mil Size Actual holdover 100 Yards 0 0 Mils 0 Mils 200 Yards 4.5” 7.2 Mils .62 Mils 300 Yards 15.9” 10.8 Mils 1.47 Mils 400 Yards 35.5” 14.4 Mils 2.46 Mils 500 Yards 64....

13 BuShnELL g2dMR ™ RETiCLE The G2DMR reticle, developed in conjunction with G.A. Precision , provides a clean reticle space while giving you the ability to range targets with extreme accuracy using .1 Mil reference points. The extended horizontal mil markings on the lower portion of the vertical cr...

14 ThE hoRiZonTAL CRoSShAiR On the horizontal crosshair, numerically designated Mil markings extend from the center of the crosshairs outward to the right in 2 Mil increments. To keep the reticle plane clean, the numbers were removed on the left side of the reticle but the reference points coincide ...

16 ThE vERTiCAL CRoSShAiR Similar to the horizontal crosshair, the vertical crosshair places the numerically designated Mil markings on only one side. Once again, the numerically designated markings are found in 2 Mil increments with hash marks every .5 Mil. Note the vertical cross hair extends to p...

18 This process works well for many cartridges and weapon systems,but not all will impact exactly the same. However this system should place you close enough to make a solid hit, all else being equal. If shooting with a different caliber or muzzle velocity, you may need to add to or subtract from th...

21 CALCuLATing hoLdS FoR Moving TARgETS The TRMR2 reticle has 14 wind dots left to right. 7 wind dots to the left and 7 wind dots to the right of center. Each dot accounts for 3,4, or 5 mph of wind depending on the Ballistic Coefficient you are using. Ballistic Coefficient Wind Dot Value .3 5 mph .4...

22 RETiCLE FRoM 10Th MiL To 38Th MiL doWn on vERTiCAL STAdiA The standard Horus grid is found from the 10th Mil down on the vertical stadia to a total of 38 Mils. The Horus grid evolves reticles beyond outdated crosshairs and mil dots. The patented grid eliminates the need to adjust windage or eleva...

23 MAinTEnAnCE Your Bushnell Elite Tactical HDMR riflescope, though amazingly tough, is a precision instrument that deserves reasonably cautious care. 1. When cleaning the lenses, first blow away any dry dirt and dust, or use a soft lens brush. Fingerprints and lubricants can be wiped off with lens ...

24 WARRAnTy / REPAiR ELiTE ® LiFETiME LiMiTEd WARRAnTy We are so proud of our Bushnell ® ELITE ® Tactical HDMR ™ Riflescopes that their materials and workmanship are warranted to be free of defects for the life of the ELITE Tactical HDMR Riflescope. The warranty is available to any owner of the ELIT...