Bunn ULTRA-2 - Manual - manualsarea.com

Page 4 - INITIAL SETUP

4 INITIAL SETUP CAUTION – The dispenser is very heavy! Use care when lifting or moving it. Use at least two people to lift or move the dispenser. 3. Remove the rear plastic plug from the trim strip between the hopper drip trays and loosen the auger motor cover screws. 2. Remove all shipping material...

Page 7 - Internal Brixing System Brix Adjustment Instructions

7 1. Apply power to machine and turn on by pressing the power button. 2. Enter the display menu by pressing the “Gourmet” button for about 5 seconds. Press and release “Gourmet” button to step through the menu to the “Test Refill” screen. Press and release the “Ice” button to select YES. 3. The Acti...

Page 8 - OPERATING CONTROLS; switch (upper left corner of the control pad)

8 OPERATING CONTROLS ULTRA-1 There are three of these switches that will be used for the operation of the dispenser. 1. switch (upper left corner of the control pad) This switch is the ON/OFF toggle switch which powers up the dispenser and the LCD display. When ON the Date and Time toggle back and f...

Page 11 - also used as back up switch in menu mode.

11 1 3 PROGRAMMING Using the menu-driven display on the front of the dispenser, the operator has the ability to alter or modify various parameters such as beverage consistency and set day/night “ON/OFF” times. The operator is also prompted to check a variety of periodic service functions or even a s...

Page 12 - PROGRAMMING THE DISPENSER; and procedures to program the various functions of the dispenser.; off o f f

12 PROGRAMMING THE DISPENSER During normal operations, the Date, the Time, and the Serial Number toggle back and forth continuously. The following function screens are in the order they appear from the menu display. Each screen will have instructions and procedures to program the various functions o...

Page 13 - MINUTE 45

13 P3678 Set Consistency This function allows the operator to adjust the ice consistency, or torque of each auger when answered YES (“ICE”). Two screens will appear for left and right. The operator can scroll through a range of a minimum of 1 (ULTRA) to a maximum of 16 (ICE). Factory default is 10. ...

Page 15 - OTHER RECOMMENDATIONS FOR YOUR DISPENSER; Programming The Dispenser on page 10 for Setting the Consistency.; PREVENTIVE MAINTENANCE; Corporation at

15 OTHER RECOMMENDATIONS FOR YOUR DISPENSER • Whether liquid concentrate or granulated powder, all product must be thoroughly mixed BEFORE adding it to the hoppers. • For best results with granita-type products, use only products with an apparent brix of 12 or higher. Some products may work with an ...

Page 17 - ASSEMBLY FOLLOWING CLEANING; Install auger nose bushing into

17 1. Install the seal(s) over the flange at the rear of the cooling drum(s) and press the seal(s) firmly into place as shown. 2. Align the auger shaft(s) with the auger(s). Push the auger(s) as far as they will go and rotate so the flat face of the auger shaft is aligned with the flat face of the a...

Page 18 - Auto-fill Cleaning Instructions; Materials required; Auto-fill Sanitizing Instructions; “auger refill on” to fill the hopper without the delay.

18 Auto-fill Cleaning Instructions (With Brixing Pump Installed) Materials required 1. Non-sudsing liquid detergent (such as common household automatic dishwasher liquid detergent). 2. Household bleach (Sodium chloride solution: 5.25%) or equivalent. 3. Clean five (5) gallon bucket. 4. Measuring Cup...

Page 19 - USER NOTICES; Risk of Electric Shock.; CHARGE; AVERTISSEMENT

19 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27442.7001 32162.0002 (ULTRA-2) 00986.7000 CHARGE Type R404A, Amount 11 oz (312 ...

Bunn ULTRA-2 - Manual

Table of Contents:

Summary

Other Bunn Models