Bromic 2620662-1 - User Manual

P3

www.

bromic

.com

P3

SEL

*

1 2 3 4 5 6

SEL

Heater 100%

- Heater output at full (100%)

Heater 66%

- Heater output at 66% of total

Heater 33%

- Heater output at 33% of total

Heater OFF

- Heater off

Lights 100% (DIM˄)

- Lights output at full (100%) or HOLD to DIM Up

Lights 50%

- Light output at 50% of total

Lights OFF (DIM˅)

- Light off or HOLD to DIM Down

SEL button:

multi-remote function

Press the SEL buttons from left or right

in order to select design zone.

BROMIC SMART-HEAT™

WIRELESS REMOTES

BY BROMIC

USER MANUAL

DESCRIPTION OF THE PRODUCT

UHF band remote with PLL controlled carrier frequency.

This type of remote is used for controlling devices for

domestic use, automatic openings, ON-OFF light control,

dimming, etc. This appliance transmits a rolling code type

signal to prevent duplication and guarantee maximum

secrecy. The remote code can be stored in the receiver

directly via the latter or via radio from the remote. With

the second possibility you can add new remotes to an

existing system without having to touch the receiver. This

can be done directly by the end user (the installer’s help is

not required). The code is stored in the receiver’s EEPROM

memory that retains it even if power is cut temporarily.

SAFETY RULES

• Do not use the manual remote in places or where

systems are sensitive to radio emissions (e.g. airports,

hospitals).

• Keep the remote out of the reach of children and

animals.

• Do not keep or use the remote in places that are damp,

where there is steam, high air humidity, dust or where

it is exposed to the direct rays of the sun or similar

environmental conditions.

• Do not let the remote drop: it could be damaged or its

range of action reduced.

• Changes or modification not expressly approved

by the party responsible for compliance could void

the user’s authority to operate the equipment.

USE

• The operator is in no way protected against interference

from other telecommunication equipment or systems

(e.g. authorised radio systems working on the same

frequency range).

• If you are having problems with its range of action, fix

the remote up high. Change the battery if necessary.

CHANGING THE BATTERY - BATTERY IS HAZARDOUS

• WARNING: Keep the batteries out of the reach of

children, whether new or used.

• If swallowed, the lithium button battery can cause

severe or fatal injuries in 2 hours or less if it is swallowed

or placed inside any part of the body.

• Medical attention should be sought immediately if it is

suspected the battery has been swallowed or placed

inside any part of the body

• Explosion hazard if the battery is substituted incorrectly.

• Replace the battery with a CR 2430 type battery only.

• Always wrap the battery up, both when it is being

stored and when it is being disposed of. The battery

should not come into contact with other metal objects

as it could cause the battery to run down, catch fire or

be damaged.

• Dispose of damaged or finished batteries immediately

in compliance with the law. To this end, contact the

authorities for safeguarding the environment or the

centre for disposing of waste materials in your area.

• Do not throw the battery away with household rubbish.

1.

Open the back cover (manual remote) or the

battery housing (wall remote).

2.

Take the old battery out and put the new one in the

same way.

Pay attention to correct polarity (+/-)!

REMOTE FIXING

If the remote is fixed on the wall with biadhesive,

the maximum holding will be reached after 24

hours from the application. Application temperature

min.+10°C (50°F).

GUARANTEE

The guarantee complies with the law. If the guarantee

has to be used please refer to the specialized retailer.

The right to the guarantee is applicable only for the

country in which the manual remote was purchased.

The batteries are not covered by the guarantee.

HOW TO STORE A REMOTE VIA RADIO WITHOUT

ACCESSING THE RECEIVER BY MEANS OF A

PREVIOUSLY STORED REMOTE

• Press the P3 button inside the already programmed

remote. The active receiver will sound continuously.

If there is no sound, the remote is not programmed

into the receiver.

• Within 5 seconds, press a button of the already

programmed remote, relative to the function to

copy. The sound will be interrupted, and continue

for another 5 seconds.

• During the sound, press a button of the new remote

that requires to be programmed. The programming

is indicated by an intermittent sound.

CONFORMITY

Bromic declares that the remotes supplied satisfy the

following technical regulations:

• FCC (Federal Communications Commission) Part

15 (FCC ID: P59TVTXI916S; P59TVEVO916S)

• IC (Industry Canada) RSS-102

(IC: 11242A-TVTXI916S; IC: 11242A-TVEVO916S)
This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

Model

Dimmer-Remote

On/Off-Remote

Dimmer-Master (42) Wireless

Remote

Carrier Frequency

916MHz (US/AU) / 868.3MHz (EU)

Modulation

FSK

Power Supply

3V ±10%

CR2430 battery

Consumption when

transmitting

10mA

Working Temperature

-10+55°C / 14+131°F

Range

30m / 100ft

DIMMER MASTER (42)

WIRELESS REMOTE

TECHNICAL DATA

The manufacturer programs each individual remote with a unique code

DIMMER REMOTE

ON/OFF REMOTE

DIM+

DIM-

OFF

100%

75%

50%

Min.

ON (1)

OFF (1)

ON (2)

OFF (2)

Keep the remote away

from Children!

Version 1.2