Page 2 - IMPORTANT INSTRUCTIONS; DANGER, WARNING, IMPORTANT; Correct disposal of this product
2 bromic.com/heat ! IMPORTANT INSTRUCTIONS This manual contains important information about the installation, operation, and maintenance of Eclipse Smart-Heat TM Electric Heaters. Please pay close attention to the important safety information shown throughout this instruction manual. Any safety info...
Page 3 - CONTENT
3 bromic.com/heat CONTENT IMPORTANT NOTES & WARNINGS 4-5 PRODUCT OVERVIEW 6 PRODUCT DESCRIPTION 6 PRODUCT SPECIFICATIONS 6 PRODUCT FEATURES 6 HEATER INSTALLATION INSTRUCTIONS 7-20 KEY DIMENSIONS & CLEARANCES 7 BOX CONTENTS 8-9 WARNING 9 INSTRUCTIONS 10-20 ELECTRICAL INSTALLATION 21 PORTABLE ...
Page 4 - IMPORTANT NOTES & WARNINGS; WARNING
4 bromic.com/heat IMPORTANT NOTES & WARNINGS WARNING • IMPORTANT - Installation MUST be carried out by a licensed electrical contractor. • Heater must be installed on level ground & by 2 persons • Improper installation, adjustment, or alteration and failure to follow the warnings and instruc...
Page 5 - IMPORTANT NOTES AND WARNINGS; CONTINUED; SAVE THESE INSTRUCTIONS
5 bromic.com/heat the place of purchase. • In case of direct connection to a supply line, a bipolar circuit breaker with contact opening distance of at least 3 mm must be fitted upstream from the supply line. Contact an authorised service technician if you are unsure if you have a circuit breaker in...
Page 6 - PRODUCT DESCRIPTION; PRODUCT FEATURES; SPECIFICATIONS
6 bromic.com/heat PRODUCT DESCRIPTION ▪ Stylish, slimline and contemporary design to suit any decor. ▪ Efficient portable space heating with 3 built in heat levels. ▪ Heaters can also be integrated into smart control systems. ▪ Wind resistant & IP54 water protection rating. ▪ Suitable for outdoo...
Page 7 - HEATER INSTALLATION INSTRUCTIONS - PORTABLE; KEY DIMENSIONS & CLEARANCES; PORTABLE
7 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... KEY DIMENSIONS & CLEARANCES The stated clearance to combustible materials represents surface temperature of 65°C above room temperature. Building & other structural material with a low heat tolerance (such as plastic,...
Page 8 - Box 2 Contents
8 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... Upper Arm Middle Arm with Large O-Ring fitted Instruction Manual (This Document) Box 2 Contents Lower Arm with Large O-Ring fitted Contents Packed in (3) Boxes Box 1 Contents Eclipse Head Assembly with 4.5m cable & plug. ...
Page 9 - Box 3 Contents
9 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... Tools/Parts Required (not Included) • Bolts for fastening to Ground surface • Phillips Head Screw Driver • Flat Head Screw Driver • Small Step Ladder • 2 strong people to help with lifting & assembly • Spirit Level Box 3 ...
Page 10 - Instructions; screws to dismantle the Base crate, allowing; 6kg per person. Forklift must be used to; until it is mounted to arm and base.
10 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... Instructions 1. Using Phillips Head screwdriver, remove 10 X screws to dismantle the Base crate, allowing the Base Cover to be uncovered. Heavy Items (>150 kg). Maximum safe lifting 16kg per person. Forklift must be used ...
Page 11 - rear compartment of the Heater Base and
11 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... 2. Remove the Base Cover and place to the side on a non-abrasive surface, to avoid scratching. 3. Remove 10 X 10 kg Base weights from the rear compartment of the Heater Base and place them nearby the desired heater location....
Page 12 - on a flat surface in desired heater location.
12 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... 4. Remove the 4 x Crate Fixing Screws from the within the Base. 5. Remove the Base from the pallet and place it on a flat surface in desired heater location. 6. NOTE: If installing in areas subject to high winds, gusts or hu...
Page 13 - compartment of the Base.; front; two mounting holes on the bottom
13 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... 7. Replace 10 X 10 kg Base Weights into the rear compartment of the Base. 8. Unwrap Lower Arm section from its packaging. 9. Fit the Lower Arm section into base, slotting the front two mounting holes on the bottom plate slot...
Page 14 - IMPORTANT
14 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... 13. Unwrap the Base Cover from its packaging and confirm that seal is fitted to the arm slot. 10. Fasten the front two slots of the Lower Arm section to the dampeners using 2 X M8 Washers, and 2X M8 Nuts. 11. Fasten the rear...
Page 15 - Note: Extra screw holes are provided in case
15 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... 15. Unwrap the Top Arm section and the Heater Head from their packaging. 14. Slide the base cover down over the Lower Arm section, allowing it to rest on top of the Base. 16. Feed the cable through the Top Arm section, and f...
Page 16 - Arm section using 2 x Slotted Head Screws; Length: 6mm) to the head to lock the angle of; NOTE: These screws will be used later to
16 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... 22. Fasten the Middle Arm section to the Top Arm section using 2 x Slotted Head Screws (M4 - Length: 6mm) with O-rings fitted. 21. Feed the Heater Head cable through the Middle Arm. 19. Unwrap the Middle Arm section from pac...
Page 17 - With the aid of another person, two if; per person
17 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... 24. With the aid of another person, two if possible, feed the Heater Head cable through the Lower Arm, and pull through the cable slack into the base. Two person lift. Maximum safe lifting 16 kg per person 25. Fasten the Mid...
Page 18 - The base MUST NOT be plugged into; DANGER
18 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... 26. Within the Base, remove 4 X Oval Head screws (#4-40 - Length: 3/8”) from the Small Connector Box, and remove lid. 27. Attach the male connector on the Heater Head cable to the female connector inside the small connector ...
Page 19 - cable, and place it in the square slot in the
19 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... 28. Attach the rubber cable grommet around the cable, and place it in the square slot in the connector box, ensuring the flat face is facing upwards. FLAT FACE - TOP 29. Fasten the Small Connector Box lid using the 4 X Oval ...
Page 20 - Rotate the Base Cover until it is in place
20 bromic.com/heat HEATER INSTALLATION INSTRUCTIONS - PORTABLE CONTINUED... 30. Rotate the Base Cover until it is in place covering the Base. 31. Fasten the Base Cover to the Base using the Dome Head Screw (M4 - Length: 6mm). 1x M4 - Length: 6mm 32. All packaging materials must be removed before tur...
Page 22 - PORTABLE HEATER CONTROL WIRING DIAGRAM; WIRING DIAGRAM
22 bromic.com/heat PORTABLE HEATER CONTROL WIRING DIAGRAM NOTES:- Supply connection must be protected with appropriate safety device, that includes isolation switch.- Electrical installation must ensure earth continuity is checked. WIRING DIAGRAM ONLY TO BE INSTALLED & SERVICED BY LICENSED &...
Page 23 - OPERATING INSTRUCTIONS; TURNING THE APPLIANCE ON; TURNING THE APPLIANCE OFF
23 bromic.com/heat OPERATING INSTRUCTIONS TURNING THE APPLIANCE ON REMOTE CONTROL FUNCTIONS 1. Plug the supply lead of the appliance into a 220-240V, 16A Outlet. 2. Switch the power outlet on. Note : You should hear a soft *beep* from within the Base, and the light will flash for 1 second. Heater wi...
Page 24 - REMOTE CONTROL BATTERY
24 bromic.com/heat OPERATING INSTRUCTIONS REMOTE CONTROL BATTERY • CAUTION: Do not ingest battery—Chemical burn hazard. • The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hour...
Page 25 - OPENING CONTROL BOX TO PAIR A NEW REMOTE; PAIRING REMOTE CONTROL TO HEATER PCB (TOP 4 BUTTONS OF REMOTE)
25 bromic.com/heat OPENING CONTROL BOX TO PAIR A NEW REMOTE 1. Switch the power supply to the Eclipse Portable Control ON. 2. With the Eclipse Portable Control powered ON, PRESS & HOLD the middle ‘ MEM ’ button on the large heater control PCB. (A long “Beep” sound should be heard whilst the butt...
Page 26 - PAIRING REMOTE CONTROL TO LED PCB (BOTTOM 3 BUTTONS OF REMOTE)
26 bromic.com/heat WARNING: MUST ONLY BE SERVICED BY LICENSED & AUTHORIZED TECHNICIAN. 1. Locate the small black button on the small LED PCB (shown in image on right), and the small button wid way down the back face of the remote (for later steps). 2. Switch the power supply to the Eclipse Porta...
Page 27 - MAINTENANCE; Lifting & Moving Hazard. Maximum safe lifting 35 lbs per person.; DO NOT
27 bromic.com/heat MAINTENANCE IMPORTANT NOTES & WARNINGS WARNING Servicing and maintenance MUST be carried out by an authorised and licenced service person only. ! WARNING If the supply cord is damaged, it must be replaced by Bromic, a service agent of Bromic or similarly qualified persons in o...
Page 28 - TROUBLESHOOTING; REPLACEMENT PARTS; SYMPTOM; Part Number
28 bromic.com/heat TROUBLESHOOTING REPLACEMENT PARTS SYMPTOM POSSIBLE CAUSE (S) CORRECTIVE ACTION No heat 1. Incorrect heater setting chosen2. Incorrect Voltage.3. No power.4. No/low batteries in remote.5. Remote too far.6. Radio interference.7. Remote not paired or faulty control. 1. Choose heat se...
