Broan Broam Elite Range Hood - Manual

Page 3 - AND; INTERIOR BLOWERS

HL0067 - 3 - RMP Series Backsplash (Stainless Steel wall covering with warming shelves. Optional) RML3336S, RML3342S,RML4548S, RML4554S orRML4560SCustom Hood Liner (optional) Model 415 7” Rd adjustable elbow (optional) 8” Rd adjustableelbow (optional) Model 412 transition (3¼” x 10” to 7”) Adapter a...

Page 4 - IN-LINE AND EXTERIOR BLOWERS

- 4 - HL006 8 RMP Series Backsplash (Stainless Steel wall covering with warming shelves. Optional) RML3336S, RML3342S,RML4548S, RML4554S or RML4560SCustom Hood Liner (optional) Model 418 10” Rd adjustable elbow (optional) Model HLB3 (280 cfm) in-line blower (includes one 8” to 10” round transition) ...

Page 5 - SELECT BLOWER OPTION AND INSTALL DUCTWORK; TYPICAL DUCTWORK; PREPARE THE INSTALLATION

- 5 - 1. SELECT BLOWER OPTION AND INSTALL DUCTWORK Either an interior or exterior blower or in-line blower may be used with this insert. The insert model RMIP33 or RMIP45 mustbe installed with blower models P5, P8, HLB3, HLB6, HLB9, HLB11, 331H, 332H, 335 or 336 only. Other blowers cannot be substit...

Page 6 - CUSTOM HOOD PREPARATION; WARNING; SUGGESTED CUSTOM HOOD INTERNAL FRAMEWORK

- 6 - 3. INSTALL BACKSPLASH (OPTIONAL) It is recommended to install the backsplash before the custom hood insert. The custom hood will cover the backsplashtop mounting screws. In order to be able to install the backsplash, make sure you have at least 18’’ clearance betweenbottom of custom hood and r...

Page 7 - CUT THE HOLE IN CUSTOM HOOD BASE

- 7 - 8. CUT THE HOLE IN CUSTOM HOOD BASE If it is not done yet, cut a hole in the bottom of the cabinet, usingthe dimensions shown beside. NOTES : 1. The notch shown in the inset must be cut only if the RMIPWC optional remote control will be installed. 2. The recommended distance from the back to t...

Page 8 - CAUTION

- 8 - 11. INSTALL THE DEVIATOR (INTERIOR BLOWER) Install the deviator as shown. NOTE : To prevent the deviator from sliding out of the rough-in plate, put some tape on the deviator base after sliding it into the rough-inplate (provided with the P5 and P8 blower) opening. If installedcorrectly, the d...

Page 10 - INSTALL THE INSERT; TOP; Take care not to kink ducting when installing insert (step 17).

- 10 - 16. DUCTING CONNECTION (ALL BLOWERS) A. When there is access to the top of the hood, connect ductwork and seal connections with duct tape after Step 17 Install the insert. B. When there is no access to the top of the hood, carefully pull down the metal duct through the custom hood base hole. ...

Page 11 - Never plug the 2-prong blower cord to the 3-prong power supply cord.

- 11 - Secure the blower by installing 2 more no. 8 x 3/8’’ screws for the P5 blower and 4 more no. 8 x 3/8’’ screws for P8 intothe locations shown in the pictures below (single blower or dual blower). Reinstall impeller(s) and cover. HD0080 HD0081 Single blower (P5) Dual blower (P8) 18. INSTALL THE...

Page 14 - SERVICE PARTS; WARRANTY

KEY PART MODEL NO. NUMBER DESCRIPTION 33 45 RANGEMASTER LOGOFILTER CLIPTHERMOSTATSPEED CONTROLSCREW NO. 8-32 x 1/2’’, QUADREXMALE CONNECTORFEMALE CONNECTORTERMINAL STRIPLOCK NUT NO 8-32SOCKET LAMPSPST DOUBLE SWITCH (HAL. LIGHT)SPST LIGHTED SINGLE SWITCH (BLOWER)SPEED CONTROL BUTTONMICROMESH FILTERS ...

Broan Broam Elite Range Hood - Manual

Table of Contents:

Summary

Other Broan Models