Page 3 - Table of Contents
INSTALLATION MANUAL SAFETY 3 READ AND SAVE THESE INSTRUCTIONS ! Intended for domestic cooking only ! INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. In U.S.A., register your range hood online at www.broan-nutone.com. In Canada, register your range hood online at www.broan.ca. ! WARNING TO REDUCE THE RI...
Page 4 - Important Safety Notice; READ AND SAVE THESE INSTRUCTIONS
INST ALLA TION MANUAL SAFETY 4 ! WARNING TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. b) Always turn hood ON when cooking at high hea...
Page 5 - CAUTION; WARNING
INSTALLATION MANUAL OPERA TION 5 Operation Always turn your hood on before you begin cooking to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and fresher. This hood is equipped w...
Page 6 - List of Materials; PARTS NOT SUPPLIED; - Ducting, conduit and all installation tools; HARDWARE PACKAGE CONTENTS BMI; PARTS SUPPLIED; - Hood with internal blower; HARDWARE PACKAGE CONTENTS BVE
INST ALLA TION MANUAL OPERA TION 6 LIGHTING/LIGHT INTENSITY CHANGE To turn the lighting ON, touch the sensor corresponding to the desired lighting intensity and the sensor will illuminate. When the lighting is ON, touch the sensor corresponding to the active light intensity to turn the lighting OFF ...
Page 7 - Installation –
INSTALLATION MANUAL CLEANING AND MAINTENANCE 7 Cleaning and Maintenance Proper maintenance of the Range Hood will assure proper performance of the unit. MOTORS The motors are permanently lubricated and never need oiling. If the motor bearings make excessive or unusual noise, replace the motor with t...
Page 8 - DUCTING; Chart A
INST ALLA TION MANUAL INST ALLA TION 8 Recommended Tools and Accessoriesfor Installation • Measuring tape • Phillips screwdriver no. 2 • Nutdriver or socket 11/32" • Flat blade screwdriver (to open knockout holes) • Drill, 1/8” drill bit and 1½” hole saw (to mark holes for ducting and cut electr...
Page 9 - WARNING FIRE HAZARD; Some Ducting Options; side wall cap
INSTALLATION MANUAL INSTALLA TION 9 Contents Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer. Make sure that the following items are included: (1) 3¼” X 10” D AMPER A SSEMBLY * (1) P ARTS B AG *** C ONTAINING : (6) N O ....
Page 10 - FRONT
INST ALLA TION MANUAL INST ALLA TION 10 Prepare the Hood 1 ] If present, remove all protective polyfilm from the hood and/or parts. 2 ] Remove 7” Round Duct Plate from top/back of hood (see illustration below). Keep the screws for further use. 3 ] Using the finger cup, remove the grease filters from...
Page 12 - A cable locking connector (not supplied) might
INST ALLA TION MANUAL INST ALLA TION 12 DUCTED INSTALLATION ONLY TIP : Inser t a small length of duct over the 3¼” x 10” damper assembly (for rectangular ducting) or 7” round (for round ducting) and seal the joint using aluminum foil duct tape to ease connection with the house duct work. 8 ] Remove ...
Page 13 - Mark mounting spread from C/L on line B. From center; WARNING: Electrical wiring must be done by a qualified person(s) in
INSTALLATION MANUAL INSTALLA TION 13 Prepare the Hood Location NOTE: Before star ting installation, read all the steps of these instructions.Use the illustration below to identify your kitchen cabinet type. EZ1 one-person installation system EZ1 installation is designed for use with kitchen cabinets...
Page 14 - RECIRCULATING KIT (REQUIRED IF NO DUCTING IS USED); Charcoal Filter Replacements; Hood Model
INST ALLA TION MANUAL INST ALLA TION 14 FRAMED CABINET 7/64” X Y Z Refer to the marking on brackets to determine the correct installation side and orientation. Mate the corresponding bracket to the cabinet side frame, while placing rear end of bracket against the wall. Use a pencil to mark 3 hole...
Page 15 - Lights; Touch Controls
INSTALLATION MANUAL INSTALLA TION 15 [ \ 7/64” X 3 X Y Z Refer to the marking on brackets to determine the correct installation side and orientation. Align the corresponding bracket to the cabinet side, while placing rear end of bracket against the wall. Draw a line on the outer edge of the brack...
Page 16 - Cleaning Stainless Steel; Aluminum Mesh Filters; Removing Aluminum Mesh Filters; Maintenance –
INST ALLA TION MANUAL INST ALLA TION 16 Install the Hood (EZ1 Bracket) 1 ] Run house power cable between service panel and hood location. 2 ] There are 2 pairs of recessed holes on each side of the top of the hood (on rear: A and B , on front C and D on illustration below); these holes allow the ran...
Page 17 - LED LIGHT STRIPS; Push the clip
INSTALLATION MANUAL INSTALLA TION 17 7 ] For framed cabinet , secure the hood to the EZ1 brackets using four (4) no. 8-18 x 1/2” metal screws (included in parts bag). Insert two (2) screws per side, in the slots (as shown in insets on illustration below). 8 ] For frameless cabinet , secure the hood ...
Page 18 - ACT Conversion; By default the maximum blower CFM is set to 600.; To verify if your installer enabled ACT
INST ALLA TION MANUAL INST ALLA TION 18 Standard Installation (without EZ1 brackets) 1 ] Use the proper diagram below for placement of duct work and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole, only cut the hole for electrical wiring. 2 ] Instal...
Page 19 - iring Diagrams
INSTALLATION MANUAL INSTALLA TION 19 Install the Hood (Standard Installation) 1 ] Run house power cable between service panel and hood location. For hood with power cable access located on back of hood, run the house power cable into the hood through the strain relief previously installed in step 6 ...
Page 20 - TROUBLESHOOTING PROCEDURES FOR BRISAS; Issue; Troubleshooting
INST ALLA TION MANUAL INST ALLA TION 20 Connect the Wiring 1 ] Connect House Power Cable to range hood wiring: BLACK to BLACK, WHITE to WHITE and GREEN or bare wire under GREEN ground screw. 2 ] Reinstall the blower cover plate (shaded par t on illustration above) using the lock nut and 7 screws pre...
Page 21 - Accessories; DESCRIPTION; Replacement Parts
INSTALLATION MANUAL WIRING DIAGRAM 21 BK G/Y BK 24 V Class 2 R BL BL R R BK ( H ) BK R ( L ) O (M ) BK ( H ) G/Y O ( M ) O (M ) BK ( H ) R ( L ) R ( L ) G/Y W W W W Transf o rm er Re f: 99 072 9 48 2A 2 1 2 1 Note: T h e contr o l boa rd is viewed w ith the connecto rs on the opposite side of the bo...