Yamaha XMV8140-D- Manuals

XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 5 • Remove the power plug from the AC outlet when cleaning the device. • Do not insert your fingers or hands in any gaps or openings on the device (vents). • Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) i...

XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 6 Contents Introduction..................................................................................................................... 7 Feat u res ..................................................................................

XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 7 Introduction Thank you for your purchase of the Yamaha XMV8280, XMV8140, XMV8280-D or XMV8140-D power amplifier. Please read through this manual carefully before beginning use, so that you will be able to take full advantage of you...

Introduction XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 8 Use the MTX Editor to update the firmware of the XMV or check the firmware version. For operation details, refer to the “MTX Editor User’s Manual.”You can download the latest firmware from the “Downloads” page on the f...

XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 9 Controls and Functions XMV8280/XMV8140 XMV8280-D/XMV8140-D q Power switch Turns power to the unit ON or OFF. Setting the switch to the upward position turns the power on; the [POWER] indicator !0 will light green. Setting the switc...

Controls and Functions XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 11 !4 [PRIMARY]/[SECONDARY] indicators (XMV8280-D/XMV8140-D only) These show the communication status of the Dante [PRI-MARY]/[SECONDARY] connectors @1 . They flash rapidly in green if the Ethernet cables are c...

Controls and Functions XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 12 XMV8280/XMV8140 XMV8280-D/XMV8140-D !9 Network connector (XMV8280/XMV8140 only) This is a 100BASE-TX Ethernet connector that allows the unit to be connected to a computer via an Ethernet cable. @0 [YDIF] con...

Controls and Functions XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 13 @1 Dante [PRIMARY]/[SECONDARY] connectors(XMV8280-D/XMV8140-D only) These are RJ-45 connectors that allow the unit to be con-nected to another Dante device such as the MTX5-D via an Ethernet cable. The Dante...

Controls and Functions XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 15  Switches 7 and 8 (START UP MODE) These specify the startup mode. @4 Analo g input connectors These are Euroblock 3-pin analog audio input connectors.For details on settings for receiving audio signals via ...

XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 16 Connections and Setting Up This chapter explains how to set up the XMV to input analog signals. If you are using the XMV along with the MTX, refer to the “MTX Setup Manual.” Refer to this manual for details regard-ing the followin...

Connections and Settin g Up XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 17 1. Loosen terminal screws. 2. Insert cables. 3. Securely ti g hten terminal screws. Pull the cables (not too strongly) to confirm that they are securely connected. 4. Bundle the cables and the Euroblock...

Connections and Settin g Up XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 18  When using low impedance connections with Double Power mode If you use Double Power mode, input/output will be dis-abled for channels B, D, F and H.Depending on the impedance (4Ω or 8Ω) of the connect...

Connections and Settin g Up XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 19  Turning the Power On Use the front panel power switch (page 9) to turn the power on.  Enabling Analog Input Using the front panel, enable analog input as follows. 1. While holdin g down the [FUNCTION...

Connections and Settin g Up XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 20  Checking the Wiring Here we’ll explain how to change the attenuation settings and switch muting on/off, which you will need to do when checking the wiring.Before you check the wiring, we recommend tha...

Connections and Settin g Up XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 21 This chapter explains how to use and connect the [REMOTE] connector and [FAULT OUTPUT] connector located on the rear panel of the XMV.  Using the [REMOTE] Connector (Euroblock 3-pin) You can connect sw...

Connections and Settin g Up XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 22  Connecting the [REMOTE] Connector or [FAULT OUTPUT] Connector You must use the supplied Euroblock plugs when making con-nections to the [REMOTE] connector or [FAULT OUTPUT] connector.If these have bee...

XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 23 Operations This chapter describes the operations you can perform from the front panel.  Basic Operations *1: “X+Y” means “operate Y w hile operating X.” For example, “[SELECT] A + encoder” means that yo u sho u ld hold do w n the...

Operations XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 24  Parameter Operations *2: “X  Y” means “operate X, and then operating Y.” For example, “[SELECT] A  encoder” means that yo u sho u ld press the [SELECT] A, and then operate the encoder. To do this... Operatin g mode ...

Operations XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 25 Execute the following procedure when you return the internal memory settings to their factory set state (initialize the internal memory), such as when the amplifier has been moved to a dif-ferent location. 1. Turn off t...

XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 26 Appendix * If taking the a b o v e steps does not sol v e the pro b lem, contact yo u r Yamaha dealer for repair. The Yamaha Pro Audio website provides a FAQ (a list of frequently asked questions, with answers). http://www.yamahap...

Appendix XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 27 If a problem occurs in the XMV, the [ALERT] indicator will flash and an alert number will appear in the display.The alert numbers, the corresponding content, and the appropriate actions are listed below. Alert Numbers and...

Appendix XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 29 Warnings and certain other types of information are displayed via the XMV8280-D/XMV8140-D front panel indicators.Messages are also displayed in the Dante Controller Error Status field.Each indicator lights or flashes as d...

Appendix XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 30 For a high-impedance connection a speaker transformer that raises the impedance to several hundred or thousand ohms is added to the speaker system. This allows the speaker system to be effectively driven with much lower c...

Appendix XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 31  Transmission Distance and Efficiency The cables that transmit electric signals have resistance. The resistance in short cables is small enough that it can be ignored, but as transmission distance and cable length increa...

XMV8280/XMV8140/XMV8280-D/XMV8140-D Owner’s Manual 234 Specifications General Specifications XMV8280 XMV8140 XMV8280-D XMV8140-D Output Power 1kHz, THD+N=1%(20 ms Burst) 4 Ω 280W 140W 280W 140W 8 Ω 280W 140W 280W 140W 4 Ω / DOUBLE POWER MODE 560W 280W 560W 280W 8 Ω / DOUBLE POWER MODE 560W 280W 560W...

XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 236 Specifications Block Diagram Dimensions Dante PRIMARY SECO N DARY YDIF In Out DSP ATT ATT -3dBFS -20dBFS -3dBFS -20dBFS -3dBFS -20dBFS DIGITAL I N PUT SE N SITI V ITY DIGITAL I N PUT SE N SITI V ITY G HA ATT AD I N PUT MIX Input:...

XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 237 Specifications  XMV8280/XMV8280-D Power Specifications (PINK NOISE, 100V/50Hz mains) Power Specifications (PINK NOISE, 120V/60Hz mains) Current Draw and Heat Dissipation MODE Line Current (A) Power Consumption (W) Watts Dissipat...

XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 240 ( w eee_e u _en_01) ( w eee_e u _de_01) ( w eee_e u _fr_01) Information for Users on Collection and Disposal of Old Equipment This sym b ol on the prod u cts, packaging, and/or accompanying doc u ments means that u sed electrical...

XMV 8 2 8 0/XMV 8 140/XMV 8 2 8 0-D/XMV 8 140-D O w ner’s Man u al 241 ( w eee_e u _es_01) ( w eee_e u _it_01) (lithi u m disposal) Información para Usuarios sobre Recolección y Disposición de Equipamiento Viejo Este sím b olo en los prod u ctos, em b alaje, y/o doc u mentación q u e se acompañe sig...