Yamaha UD-Stomp- Manuals

5 About the Backup Battery A backup battery (lithium battery) is used to keep internal data (settings) from being lost, even whenthe power cord is unplugged. Internal data will be lost when battery power is depleted, so it is recom-mended that data be stored to an external data recorder such as the ...

6 qw t er Nomenclature ■ Top Panel Display & Main Section Controller Section Footswitch Section e Utility Button (UTILITY) Enters the Utility Mode. ( → page 25) r Store Button (STORE) Enters the Store Mode. ( → page 21) t Display Displays memory numbers, parameter setting val-ues, etc. q Up Butt...

7 Nomenclature ● Controller Section y ASSIGNABLE CONTROL You can assign one of the functions of Effect Pa-rameter Controllers o - @0 to this knob. ( → page 24) u EFFECT BAND 1-8 Switches the corresponding EFFECT BAND 1-8 ON/OFF and selects an Effect Band for editing. * To switch the effect ON → OFF,...

8 @2 @3 When the knob is rotated fully to the left ( oFF ) the filter is OFF. Rotate the knob to the right to lowerthe cut off frequency. !3 FEEDBACK Control Sets the how many times the delay will repeat. !4 TAP Control Sets the timing for when the delayed sound is takenfrom the delay loop.The value...

9 @4 @5 @6 @7 @8 @9 #0 #3 #2 #1 Nomenclature ■ Rear Panel @4 Power Switch (STAND-BY ON/OFF) Power switch for the main unit. * To protect the speakers, set the OUTPUT knob @1 to “0” before switching the power ON/OFF. @5 Power Adaptor Jack (AC IN 12V 1A) Connect the supplied power adaptor to this jack...

10 INPUT EFFECT EFFECT SEND RETURN L R OUTPUT L/MONO R Instrument Guitar Amplifier, etc. UD-Stomp INPUT INPUT L R OUTPUT L/MONO R UD-Stomp Instru-ment Distortion, etc. Connections ■ Connecting the Power Use the supplied power adaptor (AC-10) to supplypower to the UD-Stomp. 1. M a k e s u r e t h e U...

11 Connections ■ Connecting an Expression (EXP) Pedal A foot controller (expression pedal), such as theYamaha FC-7 (optional) connected to the UD-Stomp’s EXP. PEDAL jack allows control of the UD-Stomp’s individual parameters with your foot. ( → page 24, 26, 27) ■ Connecting Headphones Connect a pair...

12 Using the UD-Stomp The UD-Stomp is an effects processor that is equipped with eight identical delay circuits.It provides you with the power and freedom to create complex sounds by connecting multipledelay circuits in a series, or combine any or all of the individual circuits into a single, longde...

13 6 8 7 EFFECT BAND Selecting an Effect Band Let’s first select a delay circuit and set its param-eters.The [EFFECT BAND 1-8] buttons are used to switchthe eight effect circuits ON/OFF. 1. Press the [EFFECT BAND 1] button to selectEffect Band 1 (the selected button’s lamp willflash rapidly). * When...

14 L R PAN L R PAN L R PAN Using the UD-Stomp Setting the Feedback Up to this point we have set the delay time so asingle delay sound is produced 250msec after theoriginal sound. Next, set the Feedback parameterto determine how many times the delay will repeat. 4. Rotate the FEEDBACK knob so that “ ...

15 240 msec 360 msec 360 msec 360 msec TIME Original Sound Delay sound from Effect Band 1 Delay sound fromEffect Band 2 Original Sound Delay sound fromEffect Band 1 Delay sound fromEffect Band 2 360msec TAP=100% 240msec TAP=66.6% Delay Circuit 10. In this step, set the FEEDBACK of Effect Band1 to “ ...

16 BAND 1 BAND 2 696msec 696msec BAND 1-2 1430msec Delay Output Delay Output Delay Output Delay Output BAND 1 IN 1 BAND 4 4 BAND 7 BAND 8 IN 8 BAND 5 5 BAND 2 BAND 3 IN 3 BAND 6 BAND 1 IN BAND 2 IN BAND 3 IN BAND 4 IN BAND 5 IN BAND 6 IN BAND 7 IN BAND 8 IN BAND 1 IN 1 BAND 2 7 BAND 8 BAND 3~7 BAND ...

17 Also, once a Group has been set, you can accessany of the outputs from the individual delay unitsthat make up the group. 23. Confirm that Effect Bands 1 and 2 are still com-bined into a Group ( 1-2 ) as explained above. Next, press the [EFFECT BAND 2] button toswitch ON Effect Band 2. Since Effec...

18 Two modulation waves (sine plus one more) canbe used at the same time. Press the [EFFECTBAND 2] button to switch Effect Band 2 ON,and you’ll hear the sine wave modulation onthe right channel while the other wave typemodulation is heard on the left. Setting the Phase (PHASE) When mixing the delay ...

19 Selecting and Saving Patches ■ Try Selecting Another Patch The UD-Stomp holds a total of 180 patch programs(patch) in its internal memory.The 180 patches are divided into two areas eachcontaining 10 groups, 3 banks and 3 patches. • AREA There are two areas, the USER AREA and the PRESET AREA . Whe...

20 ● Using the Foot Switch and the BankSwitch • Press a foot switch (1-3) to select the corre- sponding patch number 1-3 in the currently se-lected group/bank. • Press and hold the BANK switch until all foot switch lamps (1-3) light then remove your foot.In this condition, the following procedure ca...

21 Selecting and Saving Patches ■ Create and Store a Patch Original settings can be stored in the USER AREA(011-933). Try creating an original patch and thenstore it. ● Storing Procedure 1. Press the [STORE] button. When you enter the Store Mode, the display, the [STORE] lamp and the foot switch lam...

22 Convenient Functions Here are some convenient functions that make using the UD-Stomp easier. ● Use the Footswitch to set the DelayTime (Tap Tempo) With the UD-Stomp you can tap on the Footswitchto set the Delay Time parameter. 1. Step on and hold the BANK Footswitch until “ tAP ” appears in the d...

23 * If you want to stop loop sample playback temporarily, step on the BANK Footswitch to enter the Bypass Mode. To restartloop sample playback, press the BANK Footswitch again. * The sample loop can also be cleared by setting the FEED- BACK knob to “0” or using the [EFFECT BAND 1-8] but-tons switch...

24 External Control Settings • Fb1 - Fb8 : FEEDBACK • tP1 - tP8 : TAP • SP1 - SP8 : SPEED • dP1 - dP8 : DEPTH • Pn1 - Pn8 : PAN • LE1 - LE8 : LEVEL • EF.L : EFFECT LEVEL • di.L : DIRECT LEVEL • di.P : DIRECT PAN The controller that was assigned in step 3 can be used to control these parameters (sett...

25 Utility Mode The Utility Mode is used for settings that cover the overall system of the UD-Stomp such asthe foot switch, MIDI, external control, EXP. pedal jack, etc. * In this section, some button names have been shortened, for instance [EFFECT BAND 1] button is written as [BAND 1] button. ted f...

27 Utility Mode ● Set the External Controller Press the [BAND 3] button and use the [UP]/[DOWN]buttons to select the type of controller ( EP , 1 - 31 , 64 - 95 ). * Refer to [External Control Settings] (page 24) ● Set the Parameter to be Controlled Press the [BAND 4] button and use the [UP]/[DOWN]bu...

28 Error Messages If an error occurs during operation, one of the following error message numbers will appear inthe display. Stop operation of the device and follow the proper solution described below. E 1 : MIDI Receive Buffer Full CAUSE: Too much MIDI data is being received at one time. SOLUTION: ...

29 Specifications Digital Section • 8-Band Delay (Delay Time: 696msec max per band) • Delay Time, Loop Filter (High Cut, Low Cut), Feed- back, Tap, Pan, Level parameters can be set for each individual Effect Band. • Effect Bands can be connected in series or parallel • Effect Bands can be grouped to...

30 MIDI Implementation Chart YAMAHA [ Modulation Delay] Date:14-Dec-2001 Model UD stomp MIDI Implementation Chart Version : 1.0 +----------------------------------------------------------------------+ : : Transmitted : Recognized : Remarks : : Function ... : : : : :-------------------+--------------...

31 MIDI Implementation Chart : : : : : : : : : : : : : : : : : : : : : : : : : :-------------------+----------------+----------------+----------------: :Prog : o 0 - 127 : o 0 - 127 : : :Change : True # : ************** : : : :-------------------+----------------+----------------+----------------: :...