Yamaha MW12 - Manuals

Foreword MW12 Owner’s Manual 6 English Before Turning on the Mixer 1 Be sure that the mixer’s power switch is in the STANDBY position. Use only the PA-20 adaptor included with this mixer. Use of a different adaptor may result in equipment damage, overheating, or fire. 2 Connect the power adaptor to ...

Quick Guide MW12 Owner’s Manual 7 English Quick Guide This quick setup and operation guide covers everything from installing the Cubase LE software to using Cubase LE for recording and mixdown. While going through this section you might find it useful to also refer to the “Front and Rear Panels” sec...

MW12 Owner’s Manual 8 Quick Guide English 1 Turn the power to all gear that is to be connected to the MW12 off/standby (except the computer), and set the channel faders, ST master fader, and GROUP 1-2 fader to their minimum settings. 2 To prevent loud pops and noises, turn on the power to your sound...

Quick Guide MW12 Owner’s Manual 9 English Level Adjustment 1 The first step in adjusting levels is to set the level controls on all instruments and other sources appropriately. 2 Adjust the channel GAIN controls so that the corresponding peak indicators flash briefly on the highest peak levels (GAIN...

MW12 Owner’s Manual 10 Quick Guide English This section describes the procedure for recording via the MW12 mixer to the Cubase LE software we installed earlier. n For details on operation of the Cubase LE software refer to the pdf-format manual provided with the software. Cubase LE Setup 1 To preven...

MW12 Owner’s Manual 12 Quick Guide English 2 Use the [Stereo Switch] buttons in the Inspector to select stereo or monaural operation for the track: ( ) for stereo operation and ( ) for monaural. For the example select the stereo mode.You will normally use a monaural track when recording vocals or gu...

Quick Guide MW12 Owner’s Manual 13 English 4 To hear playback of the track you have just recorded, use either the Transport panel [Rewind] button or the ruler to rewind to the beginning of the recorded section, then click the Transport panel [Play] button. The playback level will be displayed via th...

MW12 Owner’s Manual 14 Quick Guide English 7 At this point you can begin to use EQ to refine your mix, and add effects. As an example let’s try adding reverb. Click the [Edit VST channel] button ( ) on the left side of the channel strip to open the VST Channel Settings window. Click No Effect → Reve...

Front & Rear Panels MW12 Owner’s Manual 15 English Front & Rear Panels Channel Control Section 1 GAIN Control Adjusts the input signal level.To get the best balance between the S/N ratio and the dynamic range, adjust the level so that the PEAK indicator ( 2 ) comes on only at about maximum i...

Front & Rear Panels MW12 Owner’s Manual 16 English 5 AUX1 and AUX2 Controls Sends the channel signal to the AUX 1 or AUX 2 bus. The AUX buses are normally used to feed external signal processing gear or a monitor system. The knob should generally be set close to the position. If you are using st...

Front & Rear Panels MW12 Owner’s Manual 17 English Master Control Section 1 ST Master Fader Adjusts the signal level to the ST OUT jacks. n The stereo master fader has no effect on the signal being sent to the computer via the USB interface. 2 GROUP 1-2 Fader Adjusts the signal level to the GROU...

Front & Rear Panels MW12 Owner’s Manual 18 English 7 PHANTOM +48 V Switch This switch toggles phantom power on and off. If you set the switch on, the mixer supplies power to all channels that provide XLR mic input jacks (CHs 1–4, 5/6, 7/8). Set this switch on when using one or more condenser mic...

Front & Rear Panels MW12 Owner’s Manual 19 English Rear Input/Output Section 1 Channel Input Jacks • MIC jacks (CHs 1 to 4, 5/6, 7/8) These are balanced XLR-type microphone input jacks (1:Ground; 2:Hot; 3:Cold). • LINE jacks (CHs 1 to 4) These are balanced TRS phone-type line input jacks (T:Hot;...

Front & Rear Panels MW12 Owner’s Manual 20 English 7 SEND Jacks • AUX1 and AUX2 jacks These are impedance balanced phone-type outputjacks.These jacks output the signals from the AUX1 and AUX2 buses, respectively. Use these jacks to output these signals to an effector or to a cue box or other suc...

Setting Up MW12 Owner’s Manual 21 English Setting Up Setup Procedure 1 Before connecting to microphones and instruments, be sure that all devices are turned off. Also be sure that all of the mixer’s channel faders and master control faders are set all the way down. 2 For each connection, connect one...

Setting Up MW12 Owner’s Manual 22 English Rack Mounting ■ Mounting the MW12 1 Two metal rack-mount supports are screwed onto the unit. Use a screwdriver to remove these supports. 2 Turn the supports over, and fasten them into place again using the same screws. 3 Mount the unit into the rack, and fas...

Troubleshooting MW12 Owner’s Manual 23 English Troubleshooting The MW12 mixer won’t turn on. • Is the supplied power adaptor properly plugged into both the mixer and an appropriate AC wall outlet? The system doesn’t work properly. • Are the USB cable and all necessary audio cables properly connected...

Troubleshooting MW12 Owner’s Manual 24 English • Are you recording or playing long continuous sections of audio? The audio data processing capabilities of your computer will depend on a number of factors including CPU speed and access to external devices.On Windows computers, changing some settings ...

Appendix MW12 Owner’s Manual 25 Appendix Specifications ■ Electrical Characteristics Where 0 dBu = 0.775 VrmsOutput impedance of signal generator: 150 ohms ■ General Specifications Conditions MIN TYP MAX UNIT Total Harmonic Distortion (MIC to ST OUT) (THD+N) 20 Hz-20 kHz @ +14 dBu 600 ohms, GAIN con...

Appendix MW12 Owner’s Manual 26 ■ Analog Input Specifications Where 0 dBu=0.775 Vrms and 0 dBV=1 Vrms * Input sensitivity: the lowest level that will produce an output of +4 dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are maximum posit...

Appendix MW12 Owner’s Manual 27 Dimensional Diagrams 317.4 416.6 325.6 102.6 2 108 322 480 322 When mounted on rack Unit: mm English Deutsc h Français Español

Appendix MW12 Owner’s Manual 28 Block Diagram and Level Diagram English Deutsc h Français Español

SOFTWARE LICENCING AGREEMENT MW12 Owner’s Manual 29 ATTENTION PLEASE READ THIS SOFTWARE LICENSE AGREEMENT (“AGREEMENT”) CAREFULLY BEFORE USING THIS SOFTWARE. YOU ARE ONLY PERMITTED TO USE THIS SOFTWARE PURSUANT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT. THIS AGREEMENT IS BETWEEN YOU (AS AN INDIV...