Yamaha EMX3000 - Manuals

Front and rear panel 1 EMX3000—Owner’s Manual Front and rear panel Control panel ■ Channel control section In this section, you can adjust equalization (fre-quency response), volume level, effect and moni-tor output levels for the input signal of each channel. 1 GAIN control Use this knob to adjust ...

2 Front and rear panel EMX3000—Owner’s Manual 6 Effect control (EFFECT) For each channel, this controls the amount of sig-nal that is sent to the EFFECT bus. The signal of the EFFECT bus is sent to the EFFECT jack (input/output panel A ). It is also sent to the built-in effect when the ON switch P i...

Control panel 3 EMX3000—Owner’s Manual ■ Master control section In this section, you can adjust the final level of the outputs. E MONI 1 (monitor 1) fader The MONI 1 fader adjusts the final level of the signal sent from the MONITOR 1 bus to the MONI 1 jack (input/output panel 9 ). If the Power amp s...

4 Front and rear panel EMX3000—Owner’s Manual ■ Digital effect section This section enables you to turn the built-in digi-tal effect on/off and select the effect type. M MONI 1/2 (monitor 1/2) control This knob adjusts the level of the return signal that is sent from the built-in digital effect to t...

Control panel 5 EMX3000—Owner’s Manual U LEVEL controls These knobs enable you to adjust the level of the signals input from the mixer section to the power amp section. Rotating the knob clockwise will raise the level of the input signal. Use a screw-driver of a width of 3mm or less to adjust the kn...

6 Front and rear panel EMX3000—Owner’s Manual Input/output panel 1 Channel input jacks (MIC, LINE) 1~8 These are the input jacks for channels 1~8. By using the GAIN control (control panel 1 ) you can connect any of the jacks to a wide range of sources, from mics to line-level devices (including synt...

Input/output panel 7 EMX3000—Owner’s Manual 3 Channel input jacks 9~12AChannel input jacks 9~12B These are the input jacks for channels 9/10~11/12 and are used to connect to the stereo output jacks of electronic instruments, cassette decks, or CD players. Use the A/B switch (control panel 2 ) to sel...

8 Front and rear panel EMX3000—Owner’s Manual Rear panel 1 SPEAKERS (speaker output) jacks Speakers can be connected to these jacks. The type of signals output, the number of speak-ers you can connect, and acceptable impedance differ depending on the setting of the Power amp select switch (control p...

Installation/Connections 9 EMX3000—Owner’s Manual Installation/Connections Installation The EMX3000 uses a forced cooling system with air intake on the right side and exhaust on the rear. When placing the unit, make sure that the cooling ports are not obstructed. Connection When connecting various d...

10 Installation/Connections EMX3000—Owner’s Manual Connecting input/output equipment ST1 L MONI 1 MONO(BRIDGE) ST1 RMONO 2 1 2 1 BRIDGE R/ MONO L/ MONI 1 SPEAKERS 8 Ω ~16 Ω Main Speaker • Bridge connection No connection No connection No connection No connection I O I O I O I O A A A A B B B B STSUB ...

Basic operation 11 EMX3000—Owner’s Manual Basic operation Connecting microphones and instruments 1 Before connecting mics or instruments, make sure that the power of all equip-ment (where applicable) is turned off. Also make sure that each channel fader and the faders in the master section are turne...

12 Example setups EMX3000—Owner’s Manual Example setups This section provides some ways in which the EMX3000 can be used, and explains connections and opera-tion. As a conference/entertainment hall sound system Here is an example of using the EMX3000 as a conference or entertainment hall sound syste...

As a band PA 13 EMX3000—Owner’s Manual As a band PA Here is an example of using the EMX3000 as a small PA for a band. In this example, the monitor speakers are being sent a mix that is independent of the MAIN speaker mix. An external effect such as delay or reverb is also being used. ■ Connections •...

14 Example setups EMX3000—Owner’s Manual ■ Sending an independent mix to the monitor speakers 1 Set the MONI 1 fader to the “10” posi-tion. 2 Raise the MONI 1 controls for the chan-nels that you wish to hear from the moni-tor speakers. 3 Use the MONI 1 fader of the master sec-tion to adjust the over...

Using a subwoofer 15 EMX3000—Owner’s Manual Using a subwoofer Here is an example of using a subwoofer in the speaker system. 2 1 2 1 BRIDGE R/ MONO L/ MONI 1 SPEAKERS Main speakers R 1 R 2 L 1 L 2 PFL 10 0 10 0 10 0 10 0 10 0 10 0 MONI 1 MONI 2 ST MONI 1 MONI 2 ST ST SUB 2 PFL ST SUB 1 AFL AFL AFL A...

16 Specifications EMX3000—Owner’s Manual Specifications ■ General specifications Maximum output power STEREO: 300 W+300 W/4 Ω @0.5% THD at 1 kHz 215 W+215 W/8 Ω @0.5% THD at 1 kHz BRIDGE: 600 W/8 Ω @0.5% THD at 1 kHz Frequency response 20 Hz~20 kHz +1 dB, –3 dB@1 W output into 8 Ω (SPEAKER OUT) Chan...

Input specifications 17 EMX3000—Owner’s Manual ■ Input specifications ■ Output specifications Input terminals Gain trim Actual load impedance For use with nominal Input level Connectors on mixer Sensitivity 1 1. Sensitivity is the lowest level that can produce an output of +4 dB (1.23 V) or the nomi...

18 Specifications EMX3000—Owner’s Manual Dimensions Specifications are subject to change without prior notice. For European ModelPurchaser/User Information specified in EN55103-1 and EN55103-2. Inrush Current: 85AConformed Environment: E1, E2, E3 and E4 168 W: 480 D: 454 H: 125 286 Units: mm

YAMAHA CORPORATION V699500 R0 1 IP 24 Pro Audio & Digital Musical Instrument Division P.O. Box 3, Hamamatsu, 430-8651, Japan NP Printed in Taiwan