X10 DS7000 - Manuals - manualsarea.com

Page 2 - Contents; READ THIS FIRST

3 2 Contents Introduction ................................................................................................... 4 Installation ..................................................................................................... 5 Locating Security System components ......................

Page 3 - Introduction; Installation; Locating Security System components; Locating the Security Console

5 4 Introduction The X10 Supervised Security System is built around a Security Console with anautomatic dialer that calls neighbors or friends in the event of a break in. Batterypowered RF Door/Window Sensors and Motion Detectors are used to trigger the alarm,with RF Handheld and Keychain Remote con...

Page 4 - Security Remote; Registering the Security Remote with the Security Console; Testing the Security Remote; Security Console; Mounting the console

7 6 Installation Security Remote Registering the Security Remote with the Security Console • Set the code wheel on the Security Remote to the same House Code as the Security Console. • Fit four AAA Alkaline batteries in the batter y compartment in the back of the remote. • Set the slide switch on th...

Page 5 - Installing the Door/Window Sensor; Registering the Keychain Remote with the Security Console; Keychain Remote

9 8 Installation Installing the Door/Window Sensor • Attach the Door/Window Sensor to the wall using the mounting screws provided. • Fit the Door/Window Sensor as high as possible at the top of the door/window. • Make sure the arrows on the magnetic switch halves are facing each other and that they ...

Page 6 - Testing the Motion Detector; Installing the Motion Detector; Motion Detector

11 10 Testing the Motion Detector • Set the slide switch on the Motion Detector to position 1. • Press and hold the TEST button for about a second. The LED flashes twice when you release it. • Wait 20 seconds for the sensor to settle. • Walk in front of the Motion Detector. The indicator LED lights ...

Page 7 - Installing the Lamp Module to control the security light; Installing the Power Horn; Testing the Power Horn; Power Horn

13 12 Installation Lamp Module Installing the Lamp Module to control the security light • Set the House Code and Unit Code dials to match the settings on the Security Console. This allows it to be controlled from the security light buttons on the remotes. • Plug a lamp into the Lamp Module and plug ...

Page 8 - Setting up the Dialer; Programming Phone Numbers; Modules

15 14 Setting up the Dialer Programming Phone Numbers Note: you should program the console to call a friend, relative or neighbor who can thenlisten-in to your home to determine if there is a real problem. The person can then callthe Police if necessary, or call you back to see if everything is fine...

Page 9 - Console Zone Indicators; Steady on - means that par ticular door or window is open.; Arming and Disarming the System; Using the Security System; INSTANT Mode; DELAY Mode; Arming Without a Remote

17 16 Using the Security System Console Zone Indicators The console displays the status of the first eight zones. These indicators can display fourstates, as follows: Steady on - means that par ticular door or window is open. Steady off - means that particular door or window is closed. Slow Flashing...

Page 10 - Door/Window Sensors and Motion Detectors; Clearing Remotes & Sensors from the Console; Battery Information; General

19 18 Door/Window Sensors and Motion Detectors Battery Replacement If any if the Console's zone indicators flash slowly, the Motion Detector or Door/WindowSensor for that zone has not repor ted in during the last four hours. This is most likelycaused by a dead battery. As with the remotes, as long a...

Page 11 - PROBLEM; Troubleshooting; SOLUTION

21 20 Troubleshooting If you hear a repetitive trouble alarmwhen you try to ar m the system, and itdoes not ar m. Check the zone indicators. If a door orwindow is open, its zone indicator is on.If there is a problem with a Sensor orMotion Detector, its zone indicatorflashes slowly. Either: • Press D...

Page 13 - Special Notes; Intercom Systems

25 24 Troubleshooting Troubleshooting Special Notes Intercom Systems Intercom systems which send voice signals over existing electrical wiring may interferewith the ability to control modules from your X10 security system with the intercom inuse. If the intercom system has its own separate wiring it...

Page 14 - ONE YEAR LIMITED WARRANTY

27 26 Notes Warranty ONE YEAR LIMITED WARRANTY X10 (USA) INC. (X10) WARRANTS ITS PRODUCTS TO BE FREE FROM DEFECTIVE MATERIAL ANDWORKMANSHIP FOR A PERIOD OF ONE (1) YEAR FROM THE ORIGINAL DATE OF PURCHASE AT RETAIL.X10 AGREES TO REPAIR OR REPLACE, AT ITS SOLE DISCRETION, A DEFECTIVE X10 PRODUCT IFRET...