X10 IR34A - Manual - manualsarea.com

Page 4 - Hard Key Functions; Note: Blue and Yellow text on the remote is for Home Control.

6 7 Hard Key Functions, cont. 1. HIS/HERS - Quick access keys for favorites stored under His/Hers groups. Pressing either HIS or HERS button a second time accesses the X10 Home Automation modules that you’ve set up in All Rooms . 2. SIDE KEYS - Used to access on-screen features. 3. LCD - (Liquid Cry...

Page 5 - Using the Wizard; HOME; Press the; Setup; Make; Battery Saver

8 9 Using the Wizard After you insert the batteries and choose “English” the Setup Wizard screen (1) appears. You can exit the Wizard at any time by pressing the HOME key (located just below the screen). Press any key at screen (1) to continue and follow the instructions on the screens. Pressing OK ...

Page 7 - Make sure you select the device; Setting Up Your Favorites

12 13 Setting Up Your Favorites, cont. Once you’ve gone through the Wizard and set up at least a TV, and set up more devices, or skipped the rest of them, you arrive at screen (1) to the right. Press any digit key, say digit 4, to enter a channel number. This takes you to screen (2). You can enter m...

Page 8 - Green

14 15 Setting Up X10 Devices The IR34A IconRemote - coupled with other X10 Home Automation Modules - gives you the ability to control everything electrical in your home. Once you set up your remote, you can control most any electrical device from the remote, using the keys that have been confi gured...

Page 10 - Using The Remote; Using the Remote; once; X10 RF Devices; Main Keys; Plug a lamp into the Lamp Module.; Setting up an LM465 Lamp Module (example)

18 19 Using The Remote Assuming you followed the steps on the previous pages and have set up some devices and some favorites, you can now use the remote. See the sections that follow to set up more devices and/or favorites, and to set up other functions. (See page 37 to learn how to set up more favo...

Page 11 - Sleep Macro Steps

20 21 Labeling Feature Two lines are available for labeling when you label an icon. The screen shown on the lower-right is an example of a TM751 labeled with a bath icon. The labels Bath and “Extra Bath” were associated with the icon. The following is an example of how to use the Label feature. • Pr...

Page 13 - Tips On Learning; a. Some functions from some types of remotes might not be; Line up the remotes and then press the key you want to; Learning; button to go to the

24 25 Tips On Learning The following are the guidelines that will help you use this feature: a. Some functions from some types of remotes might not be able to be learned. b. No functions may be learned under the HOME, MODE, FAVORITE, HIS, or HERS (hard) keys. c. Use fresh batteries for both the IR34...

Page 14 - Learning Main Keys; right; If you press a; left; • Check the IR transmitters/sensors are correctly aligned

26 27 Learning Main Keys At the Home screen press the Side Keys next to Setup, More, and then Learn. Then press one of the top four Side Keys K6-K9 to the right of the screen. Select the Device you want to learn keys for. In this example we only have a TV, Cable Box and Satellite Receiver set up, so...

Page 15 - Learning a Macro - Main Keys

28 29 Before learning the second key in the Macro, you can set a delay (1-10 sec.) after which the command stored in the Macro will be sent. For example, your TV might require a few seconds after turning it on before it will respond to a Channel Up/Down command. (Repeatedly press the Side Key next t...

Page 16 - Learning Side Keys

30 31 Next, point the remote you want to learn commands from at the bottom of the IR34A IconRemote, and press OK when you’re ready. (See Tips on Learning on page 25.) Learning Side Keys, cont. Next press the key on the other remote for the function you want to learn. Hold the key pressed until the s...

Page 17 - Pressing the; MODE; key and then selecting a device type

32 33 A Macro could include the Power key for your TV, followed by the Power key for your Cable box, followed (after a 2 second delay), by digit 4 from your cable remote. Then, when you later activate this Macro, it will turn on your TV, turn on your cable box, wait 2 seconds, and then set the cable...

Page 19 - Setting up more Favorites; key to display the; Setting up more; key to display the Home screen.; Then press the Side Key next to; Devices; on screen

36 37 Setting up more, cont. Setting up more Favorites When you fi rst inserted the batteries in the remote you likely went through the Wizard and set up a few favorites. You could only set up 10 favorites at that time. Here’s how to set up more favorites. Press the HOME key to display the Home scre...

Page 22 - Options; More; . Then at the screen to the right; Clear Settings

42 43 Advanced Settings Press these keys using the following sequence: HOME, Setup , More , and Advanced . The screen to the right lets you change the backlight delay; enter codes for devices directly from the printed code list that came with the remote; set up punchthrough for various devices; and ...

Page 23 - Programming Combo Device Codes; and; Punchthrough

44 45 Advanced Settings, cont. You can also change the device type by pressing the key next to the device that you are editing the code for. Pressing this key repeatedly cycles through all available device types. Programming Combo Device Codes Some Combo devices (e.g., TV/VCR, TV/DVD, DVD/VCR, etc.)...

X10 IR34A - Manual

Table of Contents:

Summary

Other X10 Models