Page 2 - IMPORTANT SAFETY INSTRUCTIONS; When using an electrical appliance, basic precaution must; READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.; This machine is for commercial use.; WARNING; Do not pick up flammable fluids, dust or vapors.
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. WARNING DANGER: Failure to read and observe all DANGER statements could result in ...
Page 3 - SAVE THESE INSTRUCTIONS
DANGER: Electrocution could occur if maintenance and repairs are performed on a unit that is notproperly disconnected from the power source. Disconnect the power supply beforeattempting any maintenance or service. WARNING: Operating a machine without observing all labels, decals, etc., could result ...
Page 4 - GROUNDING INSTRUCTIONS:
3 THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors. EXTENSION CORDS: If an extension cord is used, the wire size...
Page 5 - VACUUM AND ACCESSORIES; IMPORTANT INSTRUCTIONS; S7TOOLKIT
VACUUM AND ACCESSORIES A Motor Block B On/Off Switch C Float: Keeps liquid out of Motor Block D Polyester Filter: Remove for use with liquids E Hooks: Secure Motor Block to Tank F Suction Inlet G Tank H 2-pc. Chrome Wand I 10-ft. x 1-1/2" Flexible Hose J 2-pc PVC Wand K Universal Adapter M 3"...
Page 6 - At the end of each working day:; ELECTRIC DRAWING
5 This machine is a commercial vacuum designed for wet anddry pick-up. Dry soil can be vacuumed directly into the tank. To empty thetank of dry soil, remove the top and dump into trashreceptacle. For wet pick-up, remove polyester filter. The machine isequipped with a float shut-off. As the tank is f...
Page 7 - MOTOR REPLACEMENT; SERVICING THE VAC MOTOR
6 (Every six to twelve months): 1. Check filter for wear, replace dirt saturated filters that do not respond to normal cleaning. 2. Inspect gasket seals and replace those which have begun to leak. 3. Examine carbon motor brushes and commutator. PERIODIC MAINTENANCE The filter is accessed by lifting ...
Page 8 - CARBON BRUSH REPLACEMENT
7 CARBON BRUSH REPLACEMENT 1. Disconnect power cord from power source. 2. To access the vac motor, remove the screws that attach the main cover to thehead assembly and set the cover to oneside. 3. Remove the motor cover by removing two screws. See Figure 1 4. Remove the wire terminal from carbon bru...
Page 9 - VACUUM MOTOR ASSEMBLY; FILTER GROUP; TANK ASSEMBLY
T708/T708IE VACUUM MOTOR ASSEMBLY No. Part Num. Description Qty. 1. S81122 Cord, 120 Volt 1 S80117 Cord, 230 Volt 2. S80138 Strain Relief 1 3. S80139 Terminal Clip 1 4. S81006 Screw, 5 x 20 2 5. S80450 Terminal Block 1 6. S83733AUG6 Handle, Gray 1 7. S82627 Screw, 5 x 40 4 8. S81006 Screw, 5 x 20 2 ...
Page 12 - CART
T720TP TANK ASSEMBLY No. Part Num. Description Qty. 1. S82048 Tank – 400 1 2. S81026 Screw, M5 x 30 4 3. S83883 Plastic Washer 4 4. S83028 Hook, Latch 1 5. S82970 Release Swivel 2 6. S82969 Release Knob 2 7. S81847G6 Clamp 2 8. S81300 Rivet 4 9. S82652AG6 Hose Adapter 1 10. S82593 Deflector, Tank 1 ...
Page 13 - TSQ16 FRONT-MOUNTED SQUEEGEE; TSQ20 FRONT-MOUNTED SQUEEGEE
12 TSQ16 FRONT-MOUNTED SQUEEGEE No. Part Num. Description Qty. 1. BD705205 Hose Assembly 1 2. BD715508 Housing 1 3. BD735608 Bolt, Guide Wheel, 1/4-20 x 1.75"L. 2 4. BD735607 Guide Wheel 2 5. BD735611 Jam Nut, 1/4-20 serrated flanged 2 6. BD735609 Nylock Nut, 1/4-20 2 7. BD735602 Slotted Blade 2...
Page 14 - ACCESSORIES; *also order S82855 Retainer with Filter; LABELS; RECOMMENDED; SPARE PARTS
13 ACCESSORIES TSQ16 Front Mounted Squeegee TSQ20 Front Mounted Squeegee S72741 Paper Bag S82860 Filter Bag, Standard for 708 Model S82845 Filter Bag, Standard for T716 and T720TP S82852* Filter Cartridge, Paper, Optional for T716 and T720TP S76061* Filter Cartridge, Washable Paper, Optional for T71...
Page 15 - ffective on all products shipped; Limited Warranty; Product exceptions and Exclusions:; — continued on next page —
14 WINDSOR INDUSTRIES North American New Machine Warranty E ffective on all products shipped A FTER March 1, 2005 Limited Warranty Windsor Industries, Inc. warrants new machines against defects in material and workmanship under normal use and service to the original purchaser. Any statutory implied ...
Page 16 - Effective on all products shipped; 0 Day Warranty Extension Available; — continued from previous page —
T9003 Rev. E – 7/25/06 WINDSOR INDUSTRIES North American New Machine Warranty Effective on all products shipped AFTER March 1, 2005 cannot be identified, the warranty start date is 90 days after the date of sale to an authorized Windsor distributor. Parts replaced or repaired under warranty are guar...