Windsor SP13-10090220 - Manuals

SAFETY 86309580 FLOOR POLISHER 10/08/08 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors. D...

SAFETY 86309580 FLOOR POLISHER 10/08/08 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words – WARNING and CAUTION and FOR SAFTEY. The level of hazard intensity is det...

SAFETY 86309580 FLOOR POLISHER 10/08/08 2-3 GROUNDING INSTUCTIONS-120V THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a one 15 amp nominal 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using ...

SAFETY 86309580 FLOOR POLISHER 10/08/08 2-4 GROUNDING INSTRUCTIONS-230V THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to th...

TECHNICAL SPECIFICATIONS 86309580 FLOOR POLISHER 10/08/08 3-1 ITEM DIMENSION/CAPACITY/MODEL CONSTRUCTION Heavy-duty die cast aluminum deck with heavy-duty rubber bumper, tubular steel adjustable handle with die cast aluminum handle housing MOTOR 1HP 115V induction SP13, SP15, SP17, U17, SP17, SP20, ...

HANDLE INSTALLATION 86309580 FLOOR POLISHER 10/08/08 3-2 The handle must be installed by qualified personnel. Read all instructions thoroughly. The machine is shipped with handle unassembled. The machine is shipped with handle unassembled. Follow these steps for installation: 1. Remove handle and de...

OPERATION 86309580 FLOOR POLISHER 10/08/08 3-3 CONTROLS 1. Safety Lock – Prevents unintended operation of the machine. 2. Switch Levers – Turns machine on/off. 3. Adjustment Handle – Allows the handle to be adjusted to a comfortable operating position. HANDLE HEIGHT ADJUSTMENT NOTE: The handle is in...

OPERATION 86309580 FLOOR POLISHER 10/08/08 3-4 MACHINE OPERATION For indoor use only. When using the pad, always keep the machine moving when in contact with the floor. High starting torque. Hold machine firmly with both hands. 1. Ensure that the pad driver is in good shape. Install or change pad if...

MAINTENANCE 86309580 FLOOR POLISHER 10/08/08 4-1 SCRUB BRUSHES NOTE: All original equipment brushes are equipped with “Perform Alert © ”. This feature will tell the operator when it is time to replace the scrub brushes. “Perform Alert © ” brushes have pre-trimmed bright yellow tufts to indicate the ...

MACHINE TROUBLESHOOTING 86309580 FLOOR POLISHER 10/08/08 4-2 PROBLEM CAUSE SOLUTION Machine will not run Circuit breaker tripped in building. Check and reset. Power switch failure Test switch for continuity and replace if necessary. Tripped circuit breaker Reset. Faulty power cord Replace. Fuse in m...

DECK 86309580 FLOOR POLISHER 10/08/08/08 5-7 1 2A-2D 3 4 5 6 7 8 10 11 13 14 12 9A-9F

HANDLE 86309580 FLOOR POLISHER 10/08/08 5-9 20 11 18 4 23 14 2 26 3 7 17 5 6 27 12 13 1 9 10 8 20 24 21 25 15 22 20 8 23 18 11 19 14 16

MOTOR 86309580 FLOOR POLISHER 10/08/08 5-11 8 A-B 6 7 7 2 3 1 A-D 6 9 DUAL SPEED ONLY 5 4

SUGGESTED SPARE PARTS 86309580 FLOOR POLISHER 10/08/08 5-15 PART NO. PRV NO. SERIAL NO. FROM NOTES: 86225710 87202 WASHER, BEARING (HANDLE ADJ) 86224740 73990 SPRING, EXT .5 OD X 3.5L 86224750 73993 SPRING, COMP .48 OD X .91 L 86007110 72123 SWITCH. 25A SPST 125-250V SNAP 86215130 14344 BAR, HANDLE ...