Windsor RMBS12 - Manuals - manualsarea.com

Page 2 - MACHINE DATA LOG/OVERVIEW; YOUR DEALER; OVERVIEW

MACHINE DATA LOG/OVERVIEW ROMBUS 980124 07/02/03 2 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: __________________________________________________________________________________________________ Address: _______________________________________________________...

Page 3 - TABLE OF CONTENTS; HOW TO USE THIS MANUAL

TABLE OF CONTENTS ROMBUS 980124 07/02/03 3 Machine Data Log/Overview. ......................2Table of Contents ........................................3 HOW TO USE THIS MANUAL How to use this Manual...............................1-1 SAFETY Important Safety Instructions ......................2-1Hazar...

Page 5 - IMPORTANT SAFETY INSTRUCTIONS; When using an electrical appliance, basic precaution; READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.; SAVE THESE INSTRUCTIONS

ROMBUS 980124 07/02/03 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, electric shock, or injury: ...

Page 6 - HAZARD INTENSITY LEVEL; WARNING; CAUTION; WARNING; Use Windsor approved replacement parts.; WARNING; CAUTION

HAZARD INTENSITY LEVEL ROMBUS 980124 07/02/03 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words - WARNING and CAUTION and FOR SAFETY. The level of hazard intensity ...

Page 7 - GROUNDING INSTRUCTIONS; GROUNDING INSTRUCTIONS:

GROUNDING INSTRUCTIONS ROMBUS 980124 07/02/03 2-3 THIS PRODUCT IS FOR COMMERCIALUSE ONLY. ELECTRICAL: In the USA this machine operates on astandard 15 amp 115V, 60 hz, A.C. powercircuit . The amp, hertz, and voltage are listedon the data label found on each machine.Using voltages above or below thos...

Page 8 - TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS ROMBUS 980124 07/02/03 3-1 ITEM DIMENSION/CAPACITY Electrical 115V Nominal Power 550W Rated Amperage 7 Amps Brush Width - RMBS12 - RMBS16 12 inches (30 cm)16 inches (40 cm) Brush RPM 600 RPM Wheels 3 inches (7.5 cm) non-marking grey Dimensions – Weight - RMBS12 - RMBS16 40 l...

Page 9 - HOW THE MACHINE WORKS

HOW THE MACHINE WORKS ROMBUS 980124 07/02/03 3-2 Congratulations!You are now the proud owner of a WindsorRombus Carpet Maintainer. The Windsor Rombus Carpet Maintainer isdesigned to maintain your carpet using theRombus Quick Clean, Quick Dry Carpet CareSystem. By using the Rombus Carpet Maintainerin...

Page 10 - MACHINE OPERATION; PRE-RUN MACHINE INSPECTION; voltage is acceptable.; STARTING MACHINE; Connect the machine to a power supply.

MACHINE OPERATION ROMBUS 980124 07/02/03 3-3 PRE-RUN MACHINE INSPECTION Perform a pre-run inspection to find possibleproblems that could cause poor performance orlost time from breakdown. Check the rating plateto confirm voltage and frequency is the same asthe power supply. NOTE: A 10% variation in ...

Page 11 - MAINTENANCE; MACHINE MAINTENANCE; DAILY MAINTENANCE; PERIODIC MAINTENANCE; ANNUAL MAINTENANCE

MAINTENANCE ROMBUS 980124 07/02/03 4-1 BRUSH CLEANING ANDMAINTENANCE After each session or carpet cleaning, the brushesand the brush housing should be cleaned. Beforecleaning or changing the brushes, always unplugthe machine from the power supply. Brushes are removed without tools. Tilt and restthe ...

Page 12 - MACHINE TROUBLESHOOTING; PROBLEM

MACHINE TROUBLESHOOTING ROMBUS 980124 07/02/03 4-2 PROBLEM CAUSE SOLUTION No power to machine Dead electrical circuitbreaker in fuse box Check building circuitbreaker Faulty power cord Replace power cord Power switch failure Replace power switch Faulty circuit breaker Replace circuit breaker Interna...

Page 13 - THIS PAGE LEFT BLANK INTENTIONALLY

ROMBUS 980124 07/02/03 4-3 THIS PAGE LEFT BLANK INTENTIONALLY

Page 14 - HANDLE

HANDLE ROMBUS 980124 09/22/04 5-1 NOTE: The handle view is shown from the Rear. This is to help clarify how the components are attached to the handle asm. 11 12 13 14A14B 16 17 15 21 22 23 24A24B 20A20B 1 3 4 5 6 7 8 9 4 10 18 26 19 25 28 27

Page 20 - NOTES