Windsor QQS28 - Manuals

Windsor QQS28 – Manual in PDF format online.

Manuals:

Manual

Manual Windsor QQS28

Summary

Page 2 - MACHINE DATA LOG; OVERVIEW; The; USING THIS MANUAL; For the name and address of your dealer contact: Windsor Ind.

2 MACHINE DATA LOG MODEL DATE OF PURCHASE SERIAL NUMBER S A L E S R E P R E S E N T A T I V E # DEALER NAME OPERATIONS GUIDE NUMBER PUBLISHED Copyright 1995 Windsor Industries, Printed in USA SABER/STRIDE II 28/34 98570 5/1/98 OVERVIEW The SABER/STRIDE II is a battery powered, self propelled, hard f...

Page 3 - TABLE OF CONTENTS; OPERATIONS

3 SABER/STRIDE II 28/34 98570 10/08/98 TABLE OF CONTENTS OPERATIONS Machine Data Log . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical Specific...

Page 4 - SAFETY; HAZARD INTENSITY LEVEL; WARNING; DO NOT OPERATE MACHINE:

4 SAFETY SABER/STRIDE II 28/34 98570 7/14/98 The following symbols are used throughout this guide asindicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signalwords - WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is dete...

Page 5 - TECHNICAL SPECIFICATIONS; View: Side view of machine; Year of Construction:

5 TECHNICAL SPECIFICATIONS SABER/STRIDE II 28/34 98570 5/1/98 45” 69” View: Side view of machine MODEL: SABER/STRIDE II 28/34 Year of Construction: 1998 Nominal Power: 2.88 kW Mass: 850kg Rated Voltage: 36VDC Rated Amperage: 80 amps Cleaning Path: 28” (2 x 14”) S28, QQS2834” (2 x 17”) S34, QQS3434” ...

Page 6 - OPERATION CONTROLS; “ON”

6 OPERATION CONTROLS SABER/STRIDE II 28/34 98570 5/1/98 1. Squeegee /Vacuum Switches. Turns on and off the vacuum and squeegee system seperately if desired. 2. Brush Pressure Indicator/Switch. Sets brush pressure on floor with LED’s to show pressure level. 3. One Touch Switch. Activates scrubbing an...

Page 7 - MACHINE OPERATION; STARTING MACHINE; Before starting machine, make sure that; FILLING THE SABER/STRIDE II; Before leaving or servicing machine; SCRUBBING WITH THE SABER/STRIDE II

7 SABER/STRIDE II 28/34 98570 5/1/98 MACHINE OPERATION STARTING MACHINE NOTE: Perform pre-run machine check before operating machine. FOR SAFETY: Before starting machine, make sure that all safety devices are in place and operating properly.1. Turn the key switch clockwise to the “ON” position. Move...

Page 8 - DOUBLE SCRUB

8 SABER/STRIDE II 28/34 98570 7/14/98 MACHINE OPERATION DOUBLE SCRUB Floors which are heavily soiled or have thick accumulations of floor finish may not clean sufficiently with one pass. In these cases it will be necessary to double scrub. To double scrub, begin scrubbing as usual, but after push-in...

Page 9 - MAINTENANCE; . This feature will tell the operator when it

9 MAINTENANCE SABER/STRIDE II 28/34 98570 7/14/98 SCRUB BRUSHES NOTE: All original equipment brushes are equipped with “Perform Alert © . This feature will tell the operator when it is time to replace the scrub brushes. “Perform Alert © brushes have bright yellow tufts located on these tufts are pre...

Page 10 - NOT ENOUGH; SQUEEGEE DEFLECTION; SQUEEGEE DEFLECTION

10 MAINTENANCE SABER/STRIDE II 28/34 98570 7/14/98 SCRUB DECK SKIRT AND SQUEEGEE The skirts and squeegee should be inspected for wear and damage. The skirt is self adjusting. Replace skirt when they become cracked, worn, torn or brittle. SQUEEGEE BLADES NOTE: See page 15 of this guide for a complete...

Page 11 - ADJUSTING SQUEEGEE; The pitch adjustment on the; TO ADJUST SQUEEGEE PITCH; the key; across the entire; TIRES AND WHEELS

11 MAINTENANCE SABER/STRIDE II 28/34 98570 7/14/98 ADJUSTING SQUEEGEE Adjusting the squeegee is a two part process. First, the squeegee tool must have correct pitch in order for the squeegee blade to have the same deflection at each tip as well as the center. The pitch adjustment on the SABER/STRIDE...

Page 12 - BATTERIES; Charge batteries in a well ventilated area.; BATTERY MAINTENANCE; Do not add water until the battery is fully charged.; CHECKING BATTERY SPECIFIC GRAVITY; Use a hydrometer to check the battery specific gravity.; CHECKING GRAVITY

1 2 BATTERIES SABER/STRIDE II 28/34 98570 7/14/98 The batteries provide the power to operate the machine. The standard are four 6 volt batteries rated at 250 A/h at a 6-hour rate. The batteries require regular maintenance to keep them operating at peak efficiency. The machine batteries will hold the...

Page 13 - BATTERY CONNECTIONS SABER/STRIDE II

1 3 SABER/STRIDE II 28/34 98570 7/14/98 BATTERIES TO CHARGE THE BATTERIES When servicing machine, avoid contact with bat-tery acid. Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. Wear eye protection and protective clothing ...

Page 14 - SERVICE SCHEDULE; Maintenance Item

1 4 SERVICE SCHEDULE SABER/STRIDE II 28/34 98570 5/1/98 Maintenance Item Daily Weekly Monthly Annually Check Battery water level * Check Vac Hose Connections * Clean the Squeegee Blades * Inspect Brushes or Pads for debris ie: wire, string, wear * Inspect Vac fan shut off float screen * Drain & ...

Page 15 - II

1 5 SABER/STRIDE II 28/34 98570 9/15/98 SQUEEGEE BLADE/BRUSH HEAD OPTIONS P/N Desc. Color S28 / QQS28 S34 / QQS34 S34SP / QQS34SP 73932 FRONT, STANDARD RED X X standard 73934 REAR, STANDARD RED X standard 82529 REAR, LINATEX RED/NOTCH X option 82528 FRONT, LINATEX RED/NOTCH X X option 82638 REAR, (F...

Page 16 - SERVICE LOCATION DETAILS; ALL MODELS

1 6 SERVICE LOCATION DETAILS SABER/STRIDE II 28/34 98570 5/1/98 2 BRUSH HEAD MODELS: S28, S34, QQS28, QQS34 3 4 2 CYLINDRICAL HEAD MODELS: S34SP, QQS34SP 3 4 7 6 5 2 SQUEEGEE ASSEMBLY SQUEEGEE ASSEMBLY CYLINDRICAL HEAD (OPTION) BRUSH HEAD 1 ALL MODELS (REF. ) CONTROL PANEL REAR ELECTRICAL

Page 17 - SERVICE LOCATION PARTS LIST; Ref

SERVICE LOCATION PARTS LIST SABER/STRIDE II 28/34 98570 7/9/98 17 33 Ref Part No. Qty Description Serial No. Notes: From T o 1 70532 6 SCR, 10-32 X 1/2 PPHMS BLK 2 80657 1 PIN, COTTER HAIR .148" DIA X 3/4 QTY 2 SEE NOTE * 3 87029 2 WASHER, 5/16 FLAT SS 4 48012 2 KNOB, 5/16-18 4 PRONG 5 82191 1 P...