Windsor LB2000I - Manuals - manualsarea.com

Page 2 - MACHINE DATA LOG/OVERVIEW; OVERVIEW

MACHINE DATA LOG/OVERVIEW 86309600 (2000) BURNISHER 10/08/08 2 OVERVIEW The High Speed Burnisher is a mains powered, portable floor burnisher intended for commercial use. The appliance can be fitted with a variety of pads to perform various floor care functions. The appliance employs active dust con...

Page 3 - TABLE OF CONTENTS

TABLE OF CONTENTS 86309600 (2000) BURNISHER 10/08/08 3 Machine Data Log/Overview. ............................... 2 Table of Contents ................................................. 3 HOW TO USE THIS MANUAL How to use this Manual. ....................................... 1-1 SAFETY Important Safety...

Page 4 - HOW TO USE THIS MANUAL

HOW TO USE THIS MANUAL 86309600 (2000) BURNISHER 10/08/08 1-1 This manual contains the following sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. P...

Page 5 - SAFETY; IMPORTANT SAFETY INSTRUCTIONS; When using an electrical appliance, basic precaution; READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.; SAVE THESE INSTRUCTIONS

SAFETY 86309600 (2000) BURNISHER 10/08/08 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To r educe the risk of fire, electric shock, or injury: Use only indoors...

Page 6 - HAZARD INTENSITY LEVEL; WARNING

SAFETY 86315410 (BU2000) BURNISHER 10/08/08 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words - WARNING and CAUTION and FOR SAFETY. The level of hazard intensity is...

Page 7 - GROUNDING INSTUCTIONS-120V

SAFETY 86309600 (2000) BURNISHER 10/08/08 2-3 GROUNDING INSTUCTIONS-120V THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a one 15 amp nominal 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Usin...

Page 10 - TECHNICAL SPECIFICATIONS; ITEM

TECHNICAL SPECIFICATIONS 86309600 (2000) BURNISHER 10/08/08 3-1 ITEM DIMENSION/CAPACITY Construction Heavy-duty die cast aluminum deck with heavy-duty rubber bumper, tubular steel self adjusting handle with die cast aluminum handle housing. Motor 1.5 hp Transmission Direct drive from motor shaft. Pa...

Page 11 - OPERATION; HANDLE INSTALLATION

OPERATION 86309600 (2000) BURNISHER 10/08/08 3-2 4. Slide Bolt (item 3) through, washers (item 2), Handle Mount Brackets and Handle Assembly as shown. Tighten bolt (item 3) and nut (item 1) until the handle cannot twist in the mount bracket (45-50 foot pounds). 5. Check handle for movement up and do...

Page 12 - DAILY MAINTENANCE

OPERATION 86309600 (2000) BURNISHER 01/29/09 3-3 CONTROLS 1. Safety Lock – Prevents unintended operation of the machine. 2. Switch Levers – Turns machine on/off. OPERATION For indoor use only. When using the pad, always keep the machine moving when in contact with the floor. High starting torque. Ho...

Page 13 - MAINTENANCE; MACHINE TROUBLESHOOTING; PROBLEM

MAINTENANCE 86309600 (2000) BURNISHER 10/08/08 4-1 MACHINE TROUBLESHOOTING PROBLEM CAUSE SOLUTION Tripped circuit breaker Reset Circuit breaker tripped in building. Check and reset Fuse in motor is blown Replace CAUTION: To reduce the risk of electrical shock, unplug the machine before opening fuse ...

Page 14 - SERVICE SCHEDULE; MAINTENANCE DAILY

MAINTENANCE 86309600 (2000) BURNISHER 10/08/08 4-2 SERVICE SCHEDULE MAINTENANCE DAILY MONTHLY Check pad wear to prevent buildup of chemicals * Check pad driver system for damage * Check handles, switches, and knobs for damage * Store with pad off the floor * Check all bearings for noise * Check skir...

Page 16 - DECK

DECK 86309600 (2000) BURNISHER 10/08/08 5-1 16 2 3 12 13 14 15 9 8 7 6A-B 4 5 10 11 1

Page 18 - ELECTRICAL

ELECTRICAL 86309600 (2000) BURNISHER 10/08/08 5-3 1 2 3 4 5 6 7 8 9 10 11 12 13 A-C 14 A-B 15

Page 24 - MOTOR

MOTOR 86309600 (2000) BURNISHER 10/08/08 5-9 1 A-B 2 3 4 5 6

Page 30 - SUGGESTED SPARE PARTS

SUGGESTED SPARE PARTS 86309600 (2000) BURNISHER 10/08/08 5-15 PART NO. PRV NO. DESCRIPTION SERIAL NO. FROM NOTES: 86224740 73990 SPRING, EXT .5OD X 3.5L 86224750 73993 SPRING, COMP .48OD X .91L 86007110 72123 SWITCH, 25A SPST 125-250V SNAP 86312460 - BREAKER, 14A, VDE CIRCUIT 120V 86291460 - BREAKER...