Windsor E50 10070090 - Manuals

SAFETY INSTRUCTIONS ENSIGN 86038250 02/12/07 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, elect...

HAZARD INTENSITY LEVEL ENSIGN 86038250 02/12/07 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words - WARNING and CAUTION and FOR SAFETY. The level of hazard intensit...

SAFETY LABEL LOCATION ENSIGN 86038250 02/12/07 2-3 NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. LABEL WARNING 86242230 PRV NO. 500009

GROUNDING INSTRUCTIONS ENSIGN 86038250 02/12/07 2-4 THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a standard 15 amp 115V, 60 hz, A.C. power circuit . The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or bel...

TECHNICAL SPECIFICATIONS ENSIGN 86038250 02/12/07 3-1 ITEM MEASURE Electrical 115 Volt, 60hz Vacuum Motor Single 3 stage Solution Pump 50 psi Solution Capacity 7 gal (26 L) Recovery Capacity 6 gal (22 L) Weight - Empty 50 lbs (110 kg) Weight –Full Solution 105 lbs (230 kg) Height 35 inches (88.90 cm...

CONTROLS ENSIGN 86038250 02/12/07 3-2 1. Vacuum Switch 2. Pump Switch ON OFF OFF ON VAC PUMP 1 2

MACHINE OPERATION ENSIGN 86038250 02/12/07 3-3 GENERAL INFORMATION As the carpet is being cleaned, check to see if there is foam building up in the recovery bucket. Add a little defoaming compound to the recovery tank but never to the solution tank. For infrequent use or long periods of storage , fl...

MAINTENANCE ENSIGN 86038250 02/12/07 4-1 Unplug power cord(s) before servicing or making any repairs . DAILY MAINTENANCE 1. Flush the entire system, including floor tool, hand tool, etc., with 1 to 3 gallons of clean, hot water. 2. Vacuum out the solution tank. 3. Rinse tank with fresh water. Period...

MAINTENANCE ENSIGN 86038250 02/12/07 4-2 Only qualified maintenance personnel are to perform the following repairs . VACUUM MOTOR REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank. 3. Locate the vacuum motor wires and disconnect at the connector. 4. Remove the vacuum m...

TROUBLESHOOTING ENSIGN 86038250 02/12/07 4-4 PROBLEM CAUSE SOLUTION Dead electrical circuit Check building circuit breaker or fuse box. Loss of Power Faulty power cord Replace Equipment not grounding Follow grounding instructions exactly Receptacle not grounded Contact an electrician to check buildi...

PUMP GROUP ENSIGN 86038250 02/12/07 5-1 1 2 3 5 6 7 8 2 3 4

RECOVERY TANK GROUP ENSIGN 86038250 02/12/07 5-3 3 4 5 6 9 10 11 12 14 16 17 18 20 21 22 23 24 13 15 26 15 1 27 7 8 19 2 32 25 28 29 30 31

SOLUTION TANK GROUP ENSIGN 86038250 02/12/07 5-5 * * PARTS INSIDE TANK CONNECT TO PUMP ASM 4 5 7 8 6 6 1 2 9 10 41 6 11 12 6 14 13 15 18 19 22 20 21 17 16 23 24 28 29 30 18 31 32 33 34 35 38 37 39 39 40 36 3 26 27 25 23 42 43

VACUUM MOTOR GROUP ENSIGN 86038250 02/12/07 5-7 3 1 2 4 5

SUGGESTED SPARE PARTS ENSIGN 86038250 02/12/07 5-10 PART NO. PRV NO. DESCRIPTION SERIAL NO. FROM NOTES: 86003680 34380 FLOAT SHUT OFF 86002620 260-64A ACCESS COVER CLEAR 6” W/RIM 86161470 11-800444 ELBOW, 1.5 FS X FS 45D PVC 86256960 72142 SWITCH SPST 15A EURO ROCKER 86202160 320-05 VELCRO STRAPS 86...