Windsor ADP - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFETY INSTRUCTIONS; READ ALL INSTRUCTIONS BEFORE USING MACHINE; Use indoors only. Do not use outdoors or expose to rain.

IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING MACHINE l Connect machine to a properly grounded outlet only. See grounding instructions. l Do not leave appliance when plugged i...

Page 3 - through strain relief; CONTROLS; Before operating the ADP become familiar with; D E

Equipment Set- Up: 1. Connect hoses to dome. 2. Loop power cord through strain relief as shown. 3. Become familiar with the machine. CONTROLS Before operating the ADP become familiar with the controls located at the back of the machine and on the control panel. D E A Bush Switch B Continuous Pump Sw...

Page 8 - Using non-Windsor parts to repair this; flush the system with a neutralizing

Warning: This product contains moving parts. To reduce the risk of injury unplug the machine before servicing. Maintenance and repairs must be doneby qualified personnel ONLY. CAUTION: Using non-Windsor parts to repair this machine will void the 6-3-l warranty. Suggested Service Parts List DESCRIPTI...

Page 10 - Condition; TROUBLESHOOTING CHART; Corrective Action

Condition TROUBLESHOOTING CHART Corrective Action No Power To Machine: Dead electrical circuit breaker in fuse box Faulty power cord Power switch failure Faulty circuit breaker Internal wiring problem Electrical Shock: Equipment not grounding Receptacle not grounded Internal electrical problem Nuisa...

Page 12 - SERVICING THE VAC MOTOR; When replacing carbon vac motor; brushes loosen wire terminal; BEFORE; f armature commutator is not; Spring; Periodically check the length of the

SERVICING THE VAC MOTOR Vote: When replacing carbon vac motor brushes loosen wire terminal BEFORE removing screws on bracket f armature commutator is not tric, extremely pitted, or grooved themotor will need to be replaced or sent toa qualified service center to restore vacperformance. Important: Th...

Page 13 - VAC MOTOR ASM Parts List

VAC MOTOR ASM Parts List 2 73215 Spacer, 3/8 OD x 3 87013 Washer, Flat 4 57047 Nut, Nylock 5A 53134 Vac Motor, 11 3 Stage TD TB 5B 53183 Vac Motor, lOOV3AStageTDTB 6 20046 Clamp, 2.25 Worm Gear 7 39231 Hose, UL Vac Exhaust x 12 8 54070 Muffler Asm. ADM Vac exhaust 9 57039 Nut, 1.5 NPT flange 10 2913...

Page 14 - SHOE ASSEMBLY AND BRUSH PRESSURE MECHANISM

SHOE ASSEMBLY AND BRUSH PRESSURE MECHANISM I 98198 10/1/98

Page 16 - TANKS & VAC HOSE ASSEMBLIES

TANKS & VAC HOSE ASSEMBLIES NOTE: Each tank has a filter screen which protects the machine’s internal parts from damage.Ensure that these screens are in place and clean before operating the machine. 16 ADP 98198

Page 18 - Spray Jets; The ADP is equipped with quick change jet; Using wires or

Spray Jets The ADP is equipped with quick change jet nozzles which are easy to clean or replace. 1.) With tanks empty, tilt machine back. Rinse in hot water or use compressed air to clean. Nozzles can also be soaked in an aceticacid solution (white vinegar). CAUTION: Do not usepins or wires to clean...

Page 20 - CONTROL PANEL / MAIN HANDLE ASSEMBLY

20 98198 7/1/97 CONTROL PANEL / MAIN HANDLE ASSEMBLY

Page 22 - BRUSH DRIVE ASSEMBLY; Belt Replacement

BRUSH DRIVE ASSEMBLY Belt Replacement Periodically check the drive belt for wear. Replace worn or frayed belts before they break, when possible. To access the belt remove the belt cover. To replace the belt it is necessary to loosen the motor and remove the brush. The “preset” belt tension is correc...