Windsor 10070460 - Manuals - manualsarea.com

Page 2 - MACHINE DATA LOG/OVERVIEW; YOUR DEALER

MACHINE DATA LOG/OVERVIEW NINJA INTL 86038610 03/29/07 2 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: __________________________________________________________________________________________________ Address: _________________________________________________...

Page 3 - TABLE OF CONTENTS; OPERATIONS

TABLE OF CONTENTS NINJA INTL 86038610 03/29/07 3 Machine Data Log/Overview. ........................2 Table of Contents..........................................3 HOW TO USE THIS MANUAL How to use this Manual.................................1-1 SAFETY Important Safety Instructions .....................

Page 4 - HOW TO USE THIS MANUAL; REF –

HOW TO USE THIS MANUAL NINJA INTL 86038610 03/29/07 1-1 This manual contains the following sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts m...

Page 5 - SAFETY INSTRUCTIONS; IMPORTANT SAFETY INSTRUCTIONS; When using an electrical appliance, basic precaution; READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.; SAVE THESE INSTRUCTIONS

SAFETY INSTRUCTIONS NINJA INTL 86038610 03/29/07 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, e...

Page 6 - HAZARD INTENSITY LEVEL; WARNING; WARNING; WARNING; CAUTION

HAZARD INTENSITY LEVEL NINJA INTL 86038610 03/29/07 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words - WARNING and CAUTION and FOR SAFETY. The level of hazard inte...

Page 7 - SAFETY LABEL LOCATION

SAFETY LABEL LOCATION NINJA INTL 86038610 03/29/07 2-3 NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. LABEL CIRCUIT INTERRUPTER 86200570 PRV NO. 170-41 LABEL WARNING 86242230 PRV NO. 500009

Page 8 - GROUNDING INSTRUCTIONS; GROUNDING INSTRUCTIONS:

GROUNDING INSTRUCTIONS NINJA INTL 86038610 03/29/07 2-4 THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors. EXTENS...

Page 9 - THIS PAGE LEFT BLANK INTENTIONALLY

NINJA INTL 86038610 03/29/07 2-5 THIS PAGE LEFT BLANK INTENTIONALLY

Page 10 - TECHNICAL SPECIFICATIONS; ITEM MEASURE

TECHNICAL SPECIFICATIONS NINJA INTL 86038610 03/29/07 3-1 ITEM MEASURE ELECTRICAL 230 Volt, 50 hz Vacuum Motor Dual 2 stage Solution Pump 200 psi 500 psi Solution Capacity 10 gal (38 L) Recovery Capacity 8 gal (240 kg) Weight- Empty 110 lbs (240 kg) Weight-Full Solution 200 lbs (440 kg) Height 36 in...

Page 11 - CONTROLS; Pump Switch

CONTROLS NINJA INTL 86038610 03/29/07 3-2 1. Pump Switch 2. Vacuum #1 Switch 3. Vacuum #2 Switch CENTURY 400 BY 3 1 2

Page 12 - MACHINE OPERATION; EMPTYING AND CLEANING

MACHINE OPERATION NINJA INTL 86038610 03/29/07 3-3 PRE-RUN INSPECTION 1. Check all fittings and connectors for proper assembly. 2. Check all hoses for leaks. Repair or replace any damaged hoses. 3. Check power cord(s) for any damage. If damaged, replace. EQUIPMENT SET-UP 1. Plug power cord from mach...

Page 13 - MAINTENANCE; DAILY MAINTENANCE

MAINTENANCE NINJA INTL 86038610 03/29/07 4-1 Unplug power cord(s) before servicing or making any repairs . DAILY MAINTENANCE 1. Flush the entire system, including floor tool, hand tool, etc., with 1 to 3 gallons of clean, hot water. 2. Vacuum out the solution tank. 3. Rinse tank with fresh water. Pe...

Page 14 - following repairs

MAINTENANCE NINJA INTL 86038610 03/29/07 4-2 Only qualified maintenance personnel are to perform the following repairs . VACUUM MOTOR REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank. 3. Locate the vacuum motor wires and disconnect at the connector. 4. Remove the vacu...

Page 16 - PISTON

MAINTENANCE NINJA INTL 86038610 03/29/07 4-4 PRESSURE REGULATOR For best results with the pressure regulator, we recommend that you clean and lubricate the piston and u-cup with Superlube lubricant monthly or when pressure drop seems excessive. 1. Turn unit off before lubricating. 2. Remove cap, spr...

Page 17 - TROUBLESHOOTING; PROBLEM CAUSE

TROUBLESHOOTING NINJA INTL 86038610 03/29/07 4-5 PROBLEM CAUSE SOLUTION Dead electrical circuit Check building circuit breaker or fuse box. Loss of Power Faulty power cord Replace Equipment not grounding Follow grounding instructions exactly Receptacle not grounded Contact an electrician to check bu...

Page 26 - RECOVERY & SOLUTION TANK GROUP

RECOVERY & SOLUTION TANK GROUP NINJA INTL 86038610 03/29/07 5-9 1 4 8 9 10 11 12 13 14 15 16 16 17 18 19 20 21 22 23 24 25 26 27 23 22 28 29 30 31 32 33 34 5 6 7 10 2 3 36 35 36

Page 28 - VACUUM MOTOR GROUP

VACUUM MOTOR GROUP NINJA INTL 86038610 03/29/07 5-11 1 2 3 4 5 7 6 9 10 11 4 12 13 7 6 5 15 16 17 8 14 18 19 21 20 22