White 721 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS; FINDING MODEL NUMBER; ENGINE INFORMATION

2 TABLE OF CONTENTS Content Page Important Safe Operation Practices .................................................................................. 3 Assembling Your Snow Thrower ....................................................................................... 5 Know Your Snow Thrower ........

Page 3 - SECTION 1: IMPORTANT SAFE OPERATION PRACTICES; Training; Operation

3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of ampu...

Page 4 - Maintenance And Storage; DANGER

4 4. Never operate with a missing or damaged discharge chute. Keep all safety devices in place and working. 5. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. 6. Do not operate machine while under the influence of alcoh...

Page 5 - SECTION 2: ASSEMBLING YOUR SNOW THROWER

5 SECTION 2: ASSEMBLING YOUR SNOW THROWER Unpacking From Carton • Cut along corners of the carton and lay it down flat. Remove packing material. • Remove any loose parts included with unit (i.e., operator’s manual, etc.). • Roll unit out of carton. Check carton thoroughly for any remaining loose par...

Page 6 - Assembling Discharge Chute; SECTION 3: KNOW YOUR SNOW THROWER; Auger Control Handle

6 handle. Hold the “Z” fitting with the pliers, not the cable, to avoid damaging the cable. NOTE: The upper hole in the control handle provides for adjustment in belt tension. Refer to page 9 of thismanual for instructions. Assembling Discharge Chute • Turn the chute crank until the chute faces stra...

Page 7 - SECTION 4: OPERATING YOUR SNOW THROWER; Before Starting

7 Discharge Chute The angle of the discharge chute controls the distance that the snow is thrown. Tilt the discharge chute up for greater distance; tilt down for less distance. Loosen the hand knob on the side of the discharge chute to adjust. Tilt the chute to the desired position, and tighten the ...

Page 8 - Recoil Starter; To Stop Engine; Operating Tips

8 • If you have a grounded three-prong receptacle, proceed as follows. • Rotate choke lever to FULL position. • Connect power cord to switch box on dash panel. Plug the other end of power cord into a three-prong 120-volt, grounded, AC receptacle. • Push starter button to crank engine. As you crank t...

Page 9 - SECTION 5: MAKING ADJUSTMENTS; Shave Plate; Belt Tension; Carburetor

9 SECTION 5: MAKING ADJUSTMENTS Shave Plate • To check the adjustment of the shave plate, place the unit on a level surface. See Figure 8. The wheels, shave plate and augers should all contact level surface. Note that if the shave plate is adjusted too high, snow may blow under the housing. If the s...

Page 10 - SECTION 6: MAINTAINING YOUR SNOW THROWER; Replacing Belt; Replacing Shave Plate

10 SECTION 6: MAINTAINING YOUR SNOW THROWER Replacing Belt • Remove the belt cover by removing five hex screws. See Figure 12. Figure 12 • Pull up on the idler pulley and slip the belt off the engine pulley. • Push down on the idler pulley and slip the belt off the auger pulley. • Reassemble new bel...

Page 11 - SECTION 8: TROUBLESHOOTING GUIDE

11 SECTION 7: OFF-SEASON STORAGE • Clean snow thrower thoroughly. • Lubricate as instructed above with a light oil. • Follow “Storage” instructions in the Engine Manual. • Store in a clean, dry area. Block the snow thrower up so it is not resting on the rubber auger blades. NOTE: When storing any ty...

Page 12 - SECTION 9: PARTS LIST FOR MODEL SNOW BOSS 721

12 SECTION 9: PARTS LIST FOR MODEL SNOW BOSS 721 15 9 21 6 6 21 6 21 4 20 16 24 14 17 23 3 8 22 10 13 2 1 25 60 7 18 11 11 19 12 5 5 5 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 33 41 42 43 44 45 46 47 48 49 50 42 49 51 52 53 53 54 55 56 57 58 35 35 59

Page 16 - MANUFACTURER’S LIMITED WARRANTY FOR:

MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by White Out-door Products Co. with respect to new merchandise pur-chased and used in the United States, its possessions andterritories. White Outdoor Products Co. warrants this product againstdefects in material and ...