White W338 - Manual - manualsarea.com

Page 2 - Introduction

2 Introduction Bobbin compartment (I) Bobbin (S) Needle (R) Needle Clamp (P) Needle Clamp Screw (O) Tension Screw (Q) Take Up Lever (D) Thread Spindle (C) Thread Spool (E) Bobbin Holder (V) Bobbin Winder Spindle (T) Handwheel (K) Bobbin Spindle (U) Speed Button (L) ON/OFF Switch (A) Light Button Sti...

Page 3 - Accessories

3 Parts & Accessories Foot Pedal Jack (M) AC/DC Adapter (DC 6V) Accessories Needle Threader, Tape measure, Seam ripper, Needles, Thimble, Thread, Buttons, Pins, Scissors, Bobbins, Snaps

Page 4 - Battery Installation

4 Battery Installation Battery Installation 1. Caution: Make certain the POWER SWITCH is in the off position before inserting the batteries. 2. Insert (4)AA batteries in the battery slot compartment in the bottom of the machine. Be certain the batteries are in the correct polarities as marked on the...

Page 5 - Threading the machine

5 Threading the machine Threading the machine 1. Raise thread spindle (C) by grasping the exposed top andpulling upward until threadspindle (C) is fully extended. 2. Place thread spool (E) on the thread spindle (C) as shown. 3. Pull thread from the thread spool (E) on the thread spin-dle (C) and put...

Page 6 - Bobbin Winding and Insertion; Winding the bobbin; Bottom bobbin placement

6 Bobbin Winding and Insertion Winding the bobbin You can wind your own bobbinswith thread from spools youpurchase separately to have avirtually unlimited thread colorselection. Match your fabricsor contrast with the threadshades of your choice. 1. Always remove the bobbin (S) from the bobbin case o...

Page 7 - Operating the Sew E-Z

7 Operating the Sew E-Z Press the power switch to begin sewing. Don’tpull the fabric. Rotate the handwheel to bring the needle tothe highest position. Lift the presser foot and place fabric underthe presser foot. Lower the presser foot.

Page 8 - Controlling the Sewing Speed; To use the with foot pedal

8 Operating the Sew E-Z Controlling the Sewing Speed The machine has two speeds of sewing control.In the “H” position the switch is in, while in the“L” position the switch is out.We recommend using the slow speed at thebeginning. When you become more experienced and feel confident controlling themac...

Page 9 - Adjusting thread tension

9 Operating the Sew E-Z Adjusting thread tension Tension for maximum performance has beenset and adjusted at the factory. However, ifyou should find that stitches are too loose, ortoo tight, you can adjust the stitch. 1. Loosen stitch by turning the tension screw (Q) counter-clockwise. 2. Tighten th...

Page 10 - Changing the Needle

10 Changing the Needle 1. Turn the handwheel (K) clockwise to raise the needle(R) to its highest position. 2. Loosen the needle clamp screw (O) by turning it counter-clockwise (towardyou). You may need to use ashort slotted screwdriver or small pliers. 3. Remove the needle (R) pulling down, away fro...

Page 11 - Precautions; Troubleshooting

11 Precautions 1. The sewing machine does not run when the power switch is pressed. •Batteries are inserted incorrectly. Insert the batteries again using the diagram provided inside the battery compartment. •Batteries are exhausted. Replace with new batteries.•Make sure the Adapter (6V,1.2A) and foo...

White W338 - Manual

Table of Contents:

Summary

Other White Models