White 850W - Manual - manualsarea.com

Page 2 - TABLE OF CONTENTS; FINDING MODEL NUMBER

2 TABLE OF CONTENTS Content Page Important Safe Operation Practices................................................................... 3 Assembling Your Snow Thrower ....................................................................... 5 Know Your Snow Thrower ........................................

Page 3 - SECTION 1: IMPORTANT SAFE OPERATION PRACTICES; Engine Exhaust, some of its constituents, and cer tain vehicle; DANGER; Training

3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. ...

Page 4 - Maintenance And Storage

4 3. The clutch levers must operate easily in both directions and automatically return to the disengaged position when released. 4. Never operate with a missing or damaged discharge chute. Keep all safety devices in place and working. 5. Never run an engine indoors or in a poorly ventilated area. En...

Page 5 - SECTION 2: ASSEMBLING YOUR SNOW THROWER; Unpacking; Loose Parts; Assembly

5 SECTION 2: ASSEMBLING YOUR SNOW THROWER NOTE: Any reference in this manual to the left or rightside of the snow thrower is observed from theoperator’s position. Unpacking • Remove screws from the top sides and ends of the shipping crate. • Set panel aside to avoid tire punctures or personal injury...

Page 6 - Final Adjustments; Auger Control Adjustment; Skid Shoe Adjustment; Traction Control and Shift Lever Adjustment

6 Final Adjustments Auger Control Adjustment Check the adjustment of the auger control as follows: • Push forward on the auger control until the small rubber bumper contacts the upper handle. There should be slack in the cable. See Figure 5 . • Release the auger control. The cable should be straight...

Page 7 - SECTION 3: KNOW YOUR SNOW THROWER; Traction Control / Auger Control Lock; Auger Drive Control; Forward

7 • Recheck the adjustment and repeat adjustment as necessary. • Retighten the jam nut to secure the cable when correct adjustment is reached. NOTE: If you are uncertain that you have reached thecorrect adjustment, refer to Traction ControlAdjustment in Adjustment Section. SECTION 3: KNOW YOUR SNOW ...

Page 8 - SECTION 4: OPERATING YOUR SNOW THROWER

8 Electric Chute-Rotation Switch The electric chute-rotation switch is located on the leftside of the snow thrower dash panel. See Figure 7.To change the direction in which discharged snow isthrown, proceed as follows:• Push the toggle switch to the left to rotate the chute counterclockwise. • Push ...

Page 9 - Recoil Starter; To Engage Wheel Drive

9 • If your home electrical system is grounded, but a three-hole receptacle is not available, one should be installed by a licensed electrician before using the electric starter. • If you have a grounded three-prong receptacle, proceed as follows: • Rotate choke knob to OFF position and do not prime...

Page 10 - SECTION 5: MAKING ADJUSTMENTS; Chute Assembly Adjustment; Shift Rod Adjustment

10 snow. Adjust downward (to raise the shave plate) when using on gravel or crushed rock. • Be certain to follow the precautions found in the To Stop Engine section to prevent possible freeze-up. • Clean the snow thrower thoroughly after each use. SECTION 5: MAKING ADJUSTMENTS WARNING: NEVER attempt...

Page 11 - Drive Wheels; SECTION 6: MAINTAINING YOUR SNOW THROWER; Lubrication; Engine; Gear Shaft; Drive and Shifting Mechanism

11 Drive Wheels The wheels may be adjusted for two different methods of operation. The adjustment is made by placing the click pins in one of two different holes on the right side of the unit. See Figure 10. Figure 10 One Wheel Driving: Insert the click pin only through the outside hole of the axle ...

Page 12 - SECTION 7: SERVICING YOUR SNOW THROWER; Shave Plate and Skid Shoes; Auger Belts

12 Traction Control / Auger Control Lock The cams on the ends of the control rods which interlock the traction drive and auger drive controls must be lubricated at least once a season or every 25 hours of operation. The cams can be accessed beneath the handle panel. Use a multi-purpose automotive gr...

Page 13 - Drive Belt; Replacing Friction Wheel Rubber

13 • Drain the gasoline from the snow thrower, or place a piece of plastic film under the gas cap. • Tip the snow thrower up and forward so that it rests on its auger housing. • Remove the six self-tapping screws from the frame cover underneath the snow thrower. • Roll the front and rear auger belts...

Page 15 - SECTION 8: TROUBLE SHOOTING

15 SECTION 8: TROUBLE SHOOTING Problem Cause Remedy Engine fails to start 1. Fuel tank empty, or stale fuel. 2. Blocked fuel line. 3. Choke not in ON position 4. Faulty spark plug. 5. Safety key not in ignition switch on engine. 6. Spark plug wire disconnected. 7. Primer button not being used proper...

Page 16 - Notes

Page 28 - MANUFACTURER’S LIMITED WARRANTY FOR:

MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by White Out-door Products Co. with respect to new merchandise pur-chased and used in the United States, its possessions andterritories. White Outdoor Products Co. warrants this product againstdefects in material and ...

White 850W - Manual

Table of Contents:

Summary

Other White Models