Wet Sounds SYN DX 4 - Manuals

Page 2 - WARNING; your state has laws governing the volume of an audio system.; Please be aware; the exact locations you wish to install in.; WET SOUNDS SYN-DX SERIES AMPLIFIERS

1 CONGRATULATIONS! Thank you for purchasing the Wet Sounds SYN-DX series amplifier. Wet Sounds represents the ultimate in High Performance Marine Audio. Wet Sounds SYN-DX Series Marine Amplifiers are designed to be a complete solution for every type of extreme marine application. SYN-DX amplifiers u...

Page 3 - INSTALLATION INSTRUCTIONS; receives sufficient airflow for proper heat dissipation.; SUPPLYING ENOUGH POWER; professional technician.

2 Wet Sounds SYN-DX Series Owner’s Manual INSTALLATION INSTRUCTIONS Wet Sounds Marine Amplifiers are designed for easy installation in your boat. To ensure proper installation of your new purchase please follow all the suggestions listed below. If you do not have experience with marine electrical an...

Page 4 - RUNNING THE WIRING CABLES; possibility of inducing noise into the system**; AMPLIFIER CONNECTIONS; Power Connections; REMOTE CONNECTION

3 RUNNING THE WIRING CABLES **Always keep the signal cable and the power cables separated to prevent the possibility of inducing noise into the system** Carefully run the power and the signal cables through the boat. Always keep all the wire tight and tied down to prevent the power wire from shortin...

Page 5 - On the SYN-DX 6, there are 2 different input selection switches.

4 AMPLIFIER SIGNAL INPUTS Connect the RCA outputs from the source unit into the inputs of the amplifier. The SYN-DX Series has 1 pair of inputs for each pair of channels. SYN-DX 2 SYN-DX 4 SYN-DX 4 SYN-DX 6 SYN-DX 6 SYN-DX 2 ADVANCED SUBWOOFER CONTROLS The SYN-DX 2-Channel Amplifier is equipped with...

Page 6 - SPEAKER TERMINAL INPUTS; POWER INDICATOR; diagnostic sequence.; See troubleshooting section for further detail.

5 SPEAKER TERMINAL INPUTS The SYN-DX Series utilizes removable speaker terminal blocks for easier installations and stronger power connections. The terminal blocks are designed to accept 12 AWG- 16 AWG speaker wire. When preparing the wire you will need to strip 5/8” of the cables protective shieldi...

Page 8 - AMP DIAGRAM WITH LEGEND

1 2 3 4 5 6 7 8 7 1. Fuses – The fuses protect the amplifier against internal electrical damage and are meant to protect the amplifier only. All other power connections should be fused at the source 2. (+) 12 Volt Power – Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive termin...

Page 10 - TROUBLESHOOTING; Check your fuse and replace if necessary.; If you are experiencing problems with your amplifier after; Wet Sounds SYN-DX Fault Codes

9 TROUBLESHOOTING 1. Check your fuse and replace if necessary. 2. Confirm your Ground wire has a good connection. 3. Make sure your remote wire and power wire has +12 Volts. 4. Make sure your battery has 12 volts. 5. Confirm that the amplifier LED color is blue. If the light flashing is red than the...

Page 12 - SAMPLE SYSTEM SETUPS

11 Wet Sounds SYN-DX Series Owner’s Manual SAMPLE SYSTEM SETUPS SYN-DX 2 SYN-DX 4

Page 14 - SPECS

SYN-DX 2 SPECS Wet Sounds SYN-DX Series Owner’s Manual 13 12.21” 11.81” 11.04” 8.27” 7.39” 6.69” 0.51” 2.85” 3.08”

Page 18 - USA

Wet Sounds SYN-DX Series Owner’s Manual WET SOUNDS INC. www.wetsounds.com 877-938-7757 10621 S Sam Houston PKWY W • Suite 100 Houston, Texas 77071 USA 17

Wet Sounds SYN DX 4 - Manuals

Manuals:

User Manual Wet Sounds SYN DX 4

Summary

Wet Sounds Amplifiers Manuals